Fluke TS53 PRO Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 38

Fluke TS53 PRO Скачать руководство пользователя страница 7

3

Physical Characteristics

•

If this product is used in a manner not specified by
the manufacturer, the protection provided by the
product may be impaired.

•

To prevent unreliable test results, replace the
battery as soon as the battery icon shows no bars.

•

Before you remove the battery door, disconnect
the test leads from the line.

Physical Characteristics

Housing

See Figure 1.

The test set housing is made of high-impact plastic. The
test set provides rugged service and withstands the
rough handling and shocks associated with field use.
The housing permits operation in bad weather, such as
heavy rain or dust storms.

Belt Clip

See Figure 1.

The belt clip has a spring-loaded clip that assures a
secure connection to belt loops and D-rings. You can
replace the belt clip in the field. See "Replacing the Belt
Clip" on page 30.

Test Leads

See Figure 1.

The test set has field-replaceable test leads. Test leads
that show damage or abrasion should be replaced
before you use the test set. See "Replacing the Test
Leads" on page 31

Several different configurations of test leads are
available. See "Accessories" on page 32 for model
numbers.

Battery



Warning



Use caution when handling batteries. Do
not let the terminals short together. Dispose
of batteries properly to ensure terminals
cannot short. Disposal may be restricted by
local laws.

Note

If the test set does not operate properly, first
replace the battery and try it again before you
send the test set to Fluke Networks for repair.

A 9 V alkaline battery must be installed for the test set
to operate. Do not use a rechargeable battery.

When the battery icon on the display shows no bars,
replace the battery immediately. See "Replacing the
Battery" on page 29.

Speaker and Speakerphone Microphone

See Figure 1.

The speaker is on the back of the test set. The
speakerphone microphone is below the keypad. To
turn on the speaker, press

s

. See page 9.



Warning

Never hold the speaker against your ear
when it is on, or when turning it on or off.
Sounds emitted by the speaker can be loud
enough to damage your hearing.

Note

The speaker uses a lot of battery power. The
battery lasts longer if the speaker is used in
moderation.

«
...
5
6
7
8
9
...
»

Содержание TS53 PRO







































Отзывы:

Нет отзывов