Fluke TS53 PRO Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 38

Fluke TS53 PRO Скачать руководство пользователя страница 25

21

Using the Toner (TS54 TDR)

Using the SmartTone Function

To use the SmartTone function to identify a wire pair:

1

Turn on the test set, then connect it to a wire pair
in the cable.

2

Make sure that the test set shows 0 VDC.

3

Press

M

, press

D

to put the flashing cursor next

to

SmartTone

, then press

M

, then press

M

again

to turn on the toner.

If there is voltage on the line, the display shows

SmartTone Volt Detect Lock Out

, and toner will

not operate.

4

At the other end of the cable, use a tone probe to
find the wire pair that has the loudest tone.

5

To make sure you have found the correct pair, put
a short momentarily across the wire pair (Figure 4).
If the tone changes, you have found the correct
pair.

Notes

You cannot hear the tone on the test set.

GOL12.EPS

Figure 4. How to Use the

SmartTone Function (TS54 TDR)

Tone does not change:

Short is not on

the correct pair

Short

Tone changes:

Short is on

the correct pair

Short

«
...
23
24
25
26
27
...
»

Содержание TS53 PRO







































Отзывы:

Нет отзывов