manualshive.com logo in svg

Fluke LinkIQ, Руководство пользователя

Поделиться
Скачать
Fluke LinkIQ Скачать руководство пользователя страница 35

Cable+Network Tester

Switch Test Results

31

ACK Time

For IPv4 addresses, the length of time between when the Product sends 

the request and receives the acknowledgment from the DHCP server.
For IPv6 addresses, the DHCPv6 reply time shows. The reply time is the 

length of time between when the Product sends the DHCPv6 request and 

receives the reply response packet.

Lease Time

For IPv4 addresses, the length of time the offered address is valid. Lease 

time shows in D (days), H (hours), and M (minutes).
For IPv6 addresses, the DHCPv6 preferred-lifetime shows. The preferred-

lifetime is a the length of time in seconds that an address is in the 

preferred state and can be used without restrictions. If the preferred-

lifetime expires, the address becomes deprecated.

Note

Deprecated addresses may be used for an existing 

communication. Do not use a deprecated address for new 

communications.

DNS

With the network configured to automatically detect DHCP, up to four DNS 

server results show. IPv4 results show before IPv6 server results.
With the network configured statically, only one DNS server per protocol 

shows in the results with a maximum of two total results. For example, one 

IPv4 or one IPv6 result shows, or one of each protocol shows.

Gateway

This section shows when the Product detects the availability of a gateway 

or router.
With the network configured to automatically detect DHCP, up to four 

gateway results show. IPv4 results show before IPv6 server results.
With the network configured statically, only one gateway per protocol 

shows in the results with a maximum of two total results. For example, one 

IPv4 or one IPv6 result shows, or one of each protocol shows.

Table 13. Ping Test Results (cont.)

Item

Description

Содержание LinkIQ















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды