Fluke i400s Скачать руководство пользователя страница 2

i400s 

Calibration Information 

Safety Information 

 

XW

 Read First: Safety Information 

To ensure safe operation and service of the Current Clamp, follow these 

instructions: 

 

Read the operating instructions before use and follow all safety 

instructions. 

 

Use the Current Clamp only as specified in the operating instructions, 

otherwise the clamp’s safety features may not protect you. 

 

Adhere to local and national safety codes. Individual protective equipment 

must be used to prevent shock and arc blast injury where hazardous live 

conductors are exposed. 

 

Do not hold the Current Clamp anywhere beyond the tactile barrier, see 

Figure 1. 

 

Before each use, inspect the Current Clamp. Look for cracks or missing 

portions of the clamp housing or output cable insulation. Also look for 

loose or weakened components. Pay particular attention to the insulation 

surrounding the jaws.  

 

Never use the Current Clamp on a circuit with voltages higher than 1000 V 

CAT III or 600 V CAT IV.  

 

CAT III equipment is designed to protect against transients in 

equipment in fixed-equipment installations, such as distribution 

panels, feeders and short branch circuits, and lighting systems in 

large buildings. 

 

CAT IV equipment is designed to protect against transients from the 

primary supply level, such as an electricity meter or an overhead or 

underground utility service. 

 

Use extreme caution when working around bare conductors or bus bars. 

Contact with the conductor could result in electric shock. 

 

Use caution when working with voltages above 60 V dc or 30 V ac. Such 

voltages pose a shock hazard. 

Electrical Symbols 

 

The symbols in Table 1 appear in this document and on the Current Clamp. 

Table 1. Electrical Symbols 

Symbol 

Explanation 

,

 

Application around and removal from hazardous live conductors is permitted. 

T

 

Product is protected by double insulation. 

W

 

Risk of Danger.  Important information. See Instruction Sheet. 

X

 

Hazardous voltage. 

)

 

Conforms to relevant Canadian Standards Association directives. 

P

 

Conforms to relevant European Union directives. 

www.

.com

[email protected]

1.800.561.8187

Содержание i400s









Отзывы: