Fluke FEV300 Скачать руководство пользователя страница 8

Страница: 8 / 15

The Product Series can accept the following connection cables:

• FEV300-CON-TY2 - Type 2 plug for test adapter EV charging
• FEV300-CON-TY1 - Type 1 plug for test adapter EV charging

Steps for connecting the test adapter to the charging station:

Connect the appropriate test cable to the Product.

Connect above assembly to the charging station to be tested.

Proper test adapter connection to the charging station is shown in Figures 6,

7, and 8.

FEV300-CON-TY2

FEV300

Charging Station

Type 2

(with panel mount

socket outlet)

Figure 6. Test adapter to Type 2

with panel

FEV300-CON-TY2

FEV300

Charging Station Type 2

(with fixed cable)

Figure 7. Test adapter to Type 2

with fixed cable

FEV300

FEV300-CON-TY1

Charging Station Type 1

(with fixed cable)

Figure 8. Test adapter to Type 1 with fixed cable

Содержание FEV300
















Результаты поиска

Содержание FEV300

Отзывы:

Похожие инструкции для FEV300

Бренды по названию

Популярные бренды

Fluke FEV300, Руководство пользователя

Результаты поиска

Содержание FEV300

Отзывы:

Похожие инструкции для FEV300

Бренды по названию

Популярные бренды