background image

LIMITED WARRANTY AND LIMITATION OF LIABILITY

Each Fluke product is warranted to be free from defects in material and 

workmanship under normal use and service. The warranty period is three 

years and begins on the date of shipment. Parts, product repairs, and 

services are warranted for 90 days. This warranty extends only to the 

original buyer or end-user customer of a Fluke authorized reseller, and does 

not apply to fuses, disposable batteries, or to any product which, in Fluke's 

opinion, has been misused, altered, neglected, contaminated, or damaged 

by accident or abnormal conditions of operation or handling. Fluke warrants 

that software will operate substantially in accordance with its functional 

specifications for 90 days and that it has been properly recorded on 

nondefective media. Fluke does not warrant that software will be error free or 

operate without interruption.
Fluke authorized resellers shall extend this warranty on new and unused 

products to end-user customers only but have no authority to extend a 

greater or different warranty on behalf of Fluke. Warranty support is available 

only if product is purchased through a Fluke authorized sales outlet or 

Buyer has paid the applicable international price. Fluke reserves the right to 

invoice Buyer for importation costs of repair/replacement parts when product 

purchased in one country is submitted for repair in another country.
Fluke's warranty obligation is limited, at Fluke's option, to refund of the purchase 

price, free of charge repair, or replacement of a defective product which is 

returned to a Fluke authorized service center within the warranty period.
To obtain warranty service, contact your nearest Fluke authorized service 

center to obtain return authorization information, then send the product to 

that service center, with a description of the difficulty, postage and insurance 

prepaid (FOB Destination). Fluke assumes no risk for damage in transit. 

Following warranty repair, the product will be returned to Buyer, transportation 

prepaid (FOB Destination). If Fluke determines that failure was caused by 

neglect, misuse, contamination, alteration, accident, or abnormal condition of 

operation or handling, including overvoltage failures caused by use outside the 

product’s specified rating, or normal wear and tear of mechanical components, 

Fluke will provide an estimate of repair costs and obtain authorization before 

commencing the work. Following repair, the product will be returned to the 

Buyer transportation prepaid and the Buyer will be billed for the repair and 

return transportation charges (FOB Shipping Point).

THIS WARRANTY IS BUYER'S SOLE AND EXCLUSIVE REMEDY AND 

IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, 

INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF 

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. FLUKE 

SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR 

CONSEQUENTIAL DAMAGES OR LOSSES, INCLUDING LOSS OF DATA, 

ARISING FROM ANY CAUSE OR THEORY.

Since some countries or states do not allow limitation of the term of an 

implied warranty, or exclusion or limitation of incidental or consequential 

damages, the limitations and exclusions of this warranty may not apply to 

every buyer. If any provision of this Warranty is held invalid or unenforceable 

by a court or other decision-maker of competent jurisdiction, such holding will 

not affect the validity or enforceability of any other provision.

 

Fluke Corporation 

Fluke Europe B.V

 

P.O. Box 9090 

PO Box 1186

 

Everett, WA 98206 

5602 BD EINDHOVEN

 

U.S.A. 

The Netherlands

11/99

Содержание FEV300
















Отзывы: