manualshive.com logo in svg

Fluke 7526A, Руководство по калибровке

Поделиться
Скачать
Fluke 7526A Скачать руководство пользователя страница 12

7526A 

Calibration Manual 

4 

Specifications 

General Specifications 

Warm-up Time

 ....................................... Twice the time since last warmed up, to a maximum of 30 minutes 

Settling Time

 ......................................... Less than 5 seconds for all functions and ranges except as noted 

Standard Interfaces

 .............................. RS-232 

IEEE-488 (GPIB) 

Temperature Performance 

Operating ........................................ 0 

°

C to 50 

°

C 

Calibration (tcal)  ............................. 18 

°

C to 28 

°

C 

Storage ........................................... -20 

°

C to 70 

°

C 

Temperature Coefficient

 ....................... Temperature coefficient for temperatures outside tcal 5 

°

C is 10 % of the 90-day 

specification (or 1 year if applicable) per 

°

C 

Relative Humidity 

Operating ........................................ <80 % to 30 

°

C 

 

<70 % to 40 

°

C 

 

<40 % to 50 

°

C 

Altitude  

Operating .......................................... 3,000 m (9,800 ft) maximum  
Non-operating ................................... 12,200 m (40,000 ft) maximum 

Safety

  .................................................... EN/IEC 61010-1, ANSI/ISA 61010-1, CAN/CSA 22.2 No. 61010-1  

EMC

 ........................................................ Complies with EN/IEC 61326-1, EN/IEC 61326-2-1 for controlled EM 

environments except when used in the following conditions: 

•

  In electromagnetic fields from 0.08-2.7 GHz in excess of 1V/m. 

•

  When subjected to electrostatic discharge (ESD) to the binding posts. Good 

static awareness practices should be followed when handling this product 
such as discharging any built up static charge to the product chassis prior to 
handling terminals or test connections.  

•

  When the product is used with data I/O cables in excess of 3 m. 

 

Analog Low Isolation

 ............................ 20  V 

Line Power

 Line Voltage (selectable)  

120 V~  ................................................... 100 V to 120 V 
240 V~ .................................................... 220 V to 240 V 

Line Frequency

 ..................................... 47 to 63 Hz 

Line Voltage Variation

 .......................... 

±

10 % about setting 

Power Consumption

  ............................ 15 VA maximum 

Dimensions  

Height ............................................. 14.6 cm (5.75 inch) 
Width ............................................... 44.5 cm (17.5 inch) 
Depth .............................................. 29.8 cm (11.75 inch) overall 

Weight (without options)

 ...................... 4.24 kg (9.35 lb) 

 

Содержание 7526A













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды