Fluke 7037 Скачать руководство пользователя

Страница: 22 / 70

7037/7038/7040/7041

User's Guide

Installation

Caution

Read the

Bath Use

section before placing the bath in service.

Incorrect handling can damage the bath and void the warranty.

This bath is not designed to be portable. Therefore, moving the bath once it has

been installed should be kept to a minimum.

Warning

Never move a bath that is full of fluid. This action could be
extremely dangerous and could result in personal injury to the
person moving the bath.

If the bath is going to be placed in an area where it will need to be moved

frequently, a special cart can be designed to accommodate the bath making the

bath much more portable. Fluke Calibration sells carts designed for these baths.

However, even with a cart the bath should not be moved full of fluid. The fluid

can splash causing injury or if the bath and cart tip, the fluid could cause damage

to the surrounding area and personal injury to personnel.
If the bath must be moved, be sure to drain the fluid to prevent any injury. The

side of the bath with the compressor is heavier than the tank side. To safely

move the bath, two people are required.

Bath Environment

The bath is a precision instrument which should be located in an appropriate

environment. The location should be free of drafts, extreme temperatures and

temperature changes, dirt, etc. The surface where the bath is placed must be

level.
If used at higher temperatures where fluid vaporization is significant, a fume hood

should be used.

“Dry-out” Period

Before initial use, after transport, and any time the instrument has not been

energized for more than 10 days, the bath will need to be energized for a “dry-

out” period of 1-2 hours before it can be assumed to meet all of the safety

requirements of the IEC 1010-1.

Bath Preparation and Filling

The bath is not provided with a fluid. Various fluids are available from Fluke

Calibration and other sources. Depending on the desired temperature range, any

of the following fluids, as well as others, may be used in the bath:

•

Water

•

Ethylene

Glycol/Water

•

Methanol

•

Mineral

oil

•

Silicone

oil

Fluids are discussed in detail in the

Bath Fluid

section.

Содержание 7037







































































Результаты поиска

Содержание 7037

Отзывы:

Похожие инструкции для 7037

Бренды по названию

Популярные бренды

Fluke 7037, Руководство пользователя

Результаты поиска

Содержание 7037

Отзывы:

Похожие инструкции для 7037

Бренды по названию

Популярные бренды