manualshive.com logo in svg

Fluidwell F112-P, Руководство пользователя

Поделиться
Скачать
Fluidwell F112-P Скачать руководство пользователя страница 25

 

FW_F112P_v1901_02_EN.docx 

Page 25 

4.4.6. 

TERMINAL CONNECTORS 

Refer to Appendix A: Technical Specification 
 

 

Fig. 8: Overview of terminal connectors - Standard configuration and options 

4.4.7. 

SENSOR SUPPLY 

For type PB/PC; PX; AP:

  

There is no real sensor supply out available. Only a limited power supply is available. This power 
supply MAY NOT be used to supply the flowmeters electronics, converters etc. as it will not provide 
adequate sustained power ! All energy used by the flowmeters pick-up will directly influence the 
battery life-time. It is strongly advised to use a "zero power" pickup such as a coil or reed-switch 
when operating without external power. It is possible to use some low power NPN or PNP output 
signals, but the battery life time will be significantly reduced (consult your distributor). The sensor 
supply is fixed: 1.2V DC or 3V DC (set by the firmware). 

For type PD; PF; PM:

  

It is possible to supply the sensor with different voltages. You can set the voltage with the switches. 
Internal power is only applicable for low power sensors (Coil, Reed). External power is only available 
when the main external power supply is connected.  
The sensor supply voltage is selectable: 1.2; 3; 8.2; 12 or 24V DC. 
 

 

Содержание F112-P





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды