manualshive.com logo in svg

Fluidwell F014-P, Руководство пользователя

Поделиться
Скачать
Fluidwell F014-P Скачать руководство пользователя страница 6

Page 5 

FW-F014-P-M_v0402_05_EN.docx 

2  OPERATIONAL 

2.1 

GENERAL IN FORMATION 

 

•

 

The F014-P may only be operated by personnel who are authorized and trained by the 
operator of the facility. All instructions in this manual are to be observed  

•

 

Take careful notice of the "Safety rules, instructions and precautionary measures" in the 
front of this manual.  

This chapter describes the daily use of the F014-P. This instruction is meant for users / operators. 

2.2 

CONTROL PANEL 

The following keys are available: 

 

Fig. 2: Control panel. 

Functions of the keys 

 

 

 

This key is used to program and save new values or settings. 

It is also used to gain access to SETUP-level; please read chapter 3. 

 

 

 

This key is used to SELECT accumulated total 

The arrow-key 

 is used to increase a value after PROG has been pressed or to configure 

the F014-P; please read chapter 3. 

 

 

 

Press this key twice to CLEAR the value for total. 

The arrow-key 

is used to select a digit after PROG has been pressed or to configure the 

F014-P; please read chapter 3. 

Содержание F014-P













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды