Fluid Concepts Rear Bimini Скачать руководство пользователя страница 1

Axis Rear Bimini

2015-2019 (all models)

Instruction Manual

Congratulations on your purchase of one of the premier tow boat products in the industry!  This 

bimini top is designed to provide you years of service and satisfaction with the proper care and instal-

lation.  Please read these instructions carefully. If at any time you have a question about the bimini 

or installation, please call (480) 609-1182 and ask for technical assistance.

*****Important Safety Precautions*****  

Please Read

This Bimini is designed to used at tow boat speeds only.  Do not trailer boat while deployed.

• 

Do not allow passengers to hang on or pull on rear frame extension wihile deployed.

• 

Ensure all bolts and hardware are tightened before each use.

• 

Do not use bimini if hardware is missing or broken or if the bimini shows any type of stress (cracks, broken welds, etc).

• 

When operating or towing boat with bimini installed, be aware of low bridges, waterways, powerlines, trees, or other low objects 

• 

that may come into contact with bimini top.

Do not store surf boards or other objects on top of bimini.

• 

Failure to adhere to these safety warnings and guidelines will void warranty and may cause personal injury.

• 

Fluid Concepts

134 E. Broadway Rd. #101

Mesa, AZ  85210

(480) 609-1182

[email protected]

www.fluidconcepts.net

Содержание Rear Bimini











Отзывы: