Flowserve FlowTop V726 Скачать руководство пользователя страница 41

Страница: 41 / 68

Schmidt Armaturen

AI - FlowTop

Disassembly

Step 08

• Remove driving band (2.21)

• Remove circlip for shafts (2.23)

• Remove ring (2.22) and balancing seal ring (2.12)

CAUTION !

Do not damage stem and plug !

Reassembly

Step 08

Reassembly takes place in reverse order.

CAUTION !

Clean parts, check sealing surfaces for damage

and renew if necessary.

• Push balancing seal ring (2.12) on the plug

• Lay ring (2.22) in place

• Secure using circlip for shafts (2.23)

• Only insert guide band at "Reassembly"

Step 06

Disassemly

Step 07

• Remove packing (3.3) and bottom ring (3.2)

with Special Tool

(Packing driver tool)

CAUTION !

Do not damage packing area and guide !

Reassembly

Step 07

Reassembly takes place in reverse order.

CAUTION !

Clean parts, check packing area and guide for

damage, grease stud screws!

( Damage to the packing packing area will lead to early

leaks in the packing unit )

Lubrication as per Table 06

(Page 65)

The packing unit is confi gurated as per the

variant drawing

(Page 61 - 63)

Use new packing (3.3) !

• Tighten hexagon nuts (3.6 / 3.9) by hand fi rst

CAUTION !

The hexagon nuts (3.6 / 3.9) are tightened

at the "Reassembly" step

Step 01

Содержание FlowTop V726





































































Результаты поиска

Содержание FlowTop V726

Отзывы:

Бренды по названию

Популярные бренды

Flowserve FlowTop V726, Инструкции по разборке/сборке

Результаты поиска

Содержание FlowTop V726

Отзывы:

Бренды по названию

Популярные бренды