Flowserve FlowTop V726 Скачать руководство пользователя страница 24

Страница: 24 / 68

Schmidt Armaturen

AI - FlowTop

Disassembly

Step 02.1

• Unscrew hexagon nuts (1.4)

• Remove connection piece (4.2)

• Remove ﬂ at gasket (1.2)

CAUTION !

Remove remains of ﬂ at gasket (1.2) in the body

and in the connection piece.

Do not damage sealing surface !

Reassembly

Step 02.1

Reassembly takes place in reverse order.

CAUTION !

Clean parts and check sealing surfaces for damage.

Use new fl at gasket (1.2) !

• Lay fl at gasket (1.2) in the connection piece

• Put complete body in place

CAUTION !

Ensure it hangs vertically !

•

Grease stud screws

CAUTION !

Lubrication as per Table 06

(Page 65)

• Screw hexagon nuts in place (1.4) and tighten in a

diagonally opposite sequence using the torque wrench

CAUTION !

Nut tightening moment (1.4)

as per Table 01

(Page 64)

When tightening the nuts pay attention to the

alignment of the plug ( do not rub or insert the

plug in the open / closed movement )

Содержание FlowTop V726





































































Результаты поиска

Содержание FlowTop V726

Отзывы:

Бренды по названию

Популярные бренды

Flowserve FlowTop V726, Инструкции по разборке/сборке

Результаты поиска

Содержание FlowTop V726

Отзывы:

Бренды по названию

Популярные бренды