FlowLine EchoPod UG01-03 Скачать руководство пользователя страница 50

Страница: 50 / 52

MN310140 Rev A2

Appendix

Section Nine

FACTORY SETTINGS

EchoPod

Sensor Height

Fill-Height

UG06 Series

236.2” (600 cm)

228.2” (579.7 cm)

UG12 Series

472.4” (1200 cm)

454.4” (1154.3 cm)

USER SETTINGS

Fill out the chart below and keep as a record of your configuration.

Tank

Height =

Fill-H =

Units

Inches

Feet

Meter

Display

Air

Liquid

Safe

22mA

21 mA

20mA

Hold Last

4mA

Rev mA

4mA @ Bottom

4mA at Top

Start-up

4mA

12mA

20mA

22mA

TROUBLESHOOTING

PROBLEM

SOLUTION

No Unit Detected in
WebCal

If WebCal

cannot detect EchoPod

when connected to the computer:



Check that the LI99-2001 Fob is connected to the USB

port.



Check that all four wires (Red, Black, White and Green) are securely

attached to the Fob.



Check Device Manager and confirm that both drivers (WebCal

Configuration & EchoFob) are present.



If the above do not work, reinstall the WebCal

software while the computer

is in Safe Mode.

Cannot access some of
the configuration features
in WebCal

As choices are made in Configuration, WebCal

will begin to eliminate

functions that are not applicable to a configuration. To reset Configuration or
get access to all the features, click on the

Clear Screen

button.

Internet error. The server
name or address could not
be resolved.

This is a warning indicating that the computer configuring EchoPod

is not

connected to the Internet. Click

to continue. Flowline recommends being

connecting to the Internet during configuration. But, not being connected to the
Internet will not prevent EchoPod

from being configured.

Содержание EchoPod UG01-03





















































Результаты поиска

Содержание EchoPod UG01-03

Отзывы:

Бренды по названию

Популярные бренды

FlowLine EchoPod UG01-03, Руководство пользователя

Результаты поиска

Содержание EchoPod UG01-03

Отзывы:

Бренды по названию

Популярные бренды