FLORABEST FKS 2200 B1 Скачать руководство пользователя

Страница: 22 / 30

GB IE

Starting up a new saw chain

In the case of a new chain, the tensioning

force decreases after some time. There-

fore you must re-tension the chain after

the first 5 cuts and at longer intervals after

this.

Never attach a new chain to a

worn drive pinion or place onto

a damaged or worn chain bar.

The chain could spring back or

break, potentially leading to se-

rious injury.

Waste disposal

and environmental

protection

Do not dispose of used oil in the sewage

system or drains. Dispose of used oil in

an environmentally correct manner - bring

it to a waste disposal center.

Be environmentally friendly. Return the

tool, accessories and packaging to a recy-

cling centre when you have finished with

them.

Machines do not belong with do-

mestic waste.

Empty the oil tank carefully and hand in

your electric chainsaw at a disposal cent-

er. The plastic and metal parts employed

can be separated out and thus recycled

use can be implemented. Ask our Service-

Center for details (see P. 29 for the ad-

dress).

Maintaining the chain bar

Use cut-protection gloves when

handling the chain or the chain

bar.

The chain bar must be turned round every 10

working hours, in order to guarantee uniform

wear.

To ensure consistent wear on either side,

the bar (4) should be turned over every

about 10 hours of operation.

Turning over the bar (4) requires you to

move the tensioning screw (22) to the oth-

er side of the bar. Unscrew the retaining

bolt attaching the bar (4) to the tensioning

screw (22). Move the tensioning screw

(22) over to the other side of the bar and

screw the retaining bolt back in.

1. Switch off the saw and pull out the

power plug.

2. Remove the sprocket chain wheel

covering, the saw chain and the chain

bar.

3. Check the chain bar for wear. Remove

burrs and straighten the guide sur-

faces with a flat file.

4. Clean the oil passages of the chain

bar (

26), in order to guarantee a

trouble-free, automatic oiling of the

saw chain during operation.

5. Mount chain bar, chainsaw and

sprocket chain wheel covering and

tighten the chainsaw.

With the oil nozzles in good condition

and the oil regulator set correctly, the

saw chain will spray a little oil off after

starting.

Содержание FKS 2200 B1































Результаты поиска

Содержание FKS 2200 B1

Отзывы:

Похожие инструкции для FKS 2200 B1

Бренды по названию

Популярные бренды

FLORABEST FKS 2200 B1, Руководство по эксплуатации

Результаты поиска

Содержание FKS 2200 B1

Отзывы:

Похожие инструкции для FKS 2200 B1

Бренды по названию

Популярные бренды