background image

 

15 

MAINTENANCE 

Check cable-entry seals periodically. Tighten and/or apply sealant if needed. This 
is especially important in environments containing heavy concentrations of dust, 
oil mist, or other residue. 

Check all wiring connections occasionally for oxidation or corrosion. Clean and re-
seat if such conditions are noted. 

If necessary, check and re-seat any connections that may have been subjected to 
strain (during rework or construction, for example). 
 

REPLACING BATTERY 

NOTE:

  The QSI2 and QSI3 communications module has a 3V lithium coin cell 

battery installed on the PC board.  In case of power failure, the battery functions 
as power backup to maintain the internal system time. Any QSI2 or QSI3 feature 
that uses a time reference as part of its functionality will be immediately accurate 
to the current time when power is restored. 

To replace battery in 

“NO DISPLAY”

 MODULE: 

 

DISCONNECT POWER TO METER 

  Remove (6) screws retaining the cover plate to the base and lift the cover plate 

free of the base (see Figure 12). 

  Flip  the  cover  plate  over  and  remove  (4)  screws  retaining  the  PC  board 

assembly (see Figure 13). 

  Remove  and  replace  the  coin  cell  battery  (CR2032)  on  the  backside  of  PC 

board (see Figure 14). 

  Reverse the procedure to reassemble the cover plate to the base. Make sure 

the cover plate seal is seated before tightening the (6) cover plate screws. 

 

To replace battery in 

“DISPLAY READY”

 MODULE: 

NOTE:

 On units with a display, only the display needs to be removed to replace 

the  coin  cell  battery.  The  battery  is  accessible  through  the  opening  where  the 
display is installed (see Figure 15). 

 

DISCONNECT POWER TO METER 

  Remove  (4)  screws  retaining  the  display  to  the  cover  plate.  Lift  the  display 

straight  up  to  disconnect  the 10-pin bridge  connector.  The  bridge connector 
could disengage from either socket connector (display or PCB assembly) or 
both. 

  Remove and replace the coin cell battery (CR2032). 

  Reverse the procedure to reassemble the display to the cover plate. Make sure 

the display seal is seated before tightening the (4) display screws. 

 

 

Содержание QSI1





















Отзывы: