Flintec FAA-27 Скачать руководство пользователя страница 20

Страница: 20 / 22

FAA-27, Technical Manual, Rev. 1.1, June 2014

Page 19 of 21

8. Programming With xFace Software Over RS232

FAA-27 has RS232C serial interface to perform eCal electronic calibration and to
adjust filter, setpoint values and to follow status by using

xFace

software installed on

a PC.
For installing the xFace software, which is supplied with the instrument or can be
downloaded from

www.flintec.com

, follow the steps described below.

8.1 Installation Of xFace Software



Close all applications on your PC



Insert the CD that contains the xFace software v2.03 or higher into the CD-

ROM drive



ouble click “Setup.exe” to start the installation. The setup Wizard will be

displayed.



Follow the menus in the setup wizard step by step.



After finishing the installation, the Setup Wizard will inform you about the

success of the software installation. Click the OK button.



After closing the Setup Wizard you can start to use the xFace software.

8.2 Connection To The xFace Software

For programming instrument via xFace follow the instructions below;

1. Power off the instrument.

2. Connect the instrument to PC as

shown in

chapter 4.5

to use xFace

software and run the software.
Select FAA-27 and press

“OK”

button.

3. Select the Com-port and press on

“Connect” to connect to the
instrument.

Содержание FAA-27























Результаты поиска

Содержание FAA-27

Отзывы:

Похожие инструкции для FAA-27

Бренды по названию

Популярные бренды

Flintec FAA-27, Техническое руководство

Результаты поиска

Содержание FAA-27

Отзывы:

Похожие инструкции для FAA-27

Бренды по названию

Популярные бренды