Flintec FAA-27 Скачать руководство пользователя страница 2

Страница: 2 / 22

FAA-27, Technical Manual, Rev. 1.1, June 2014

Page 1 of 21

Table of Contents

Safety Instructions ........................................................................... 2

Declaration Of Conformity ............................................................... 3

Front View, Features And Specifications ......................................... 4

Installation And Commissioning ....................................................... 7

4.1 Mechanical Installation .................................................................. 8

4.2 Load Cell Connection .................................................................... 8

4.3 Analogue Output Connection ........................................................ 8

4.4 Changing The Analogue Output .................................................... 9

4.5 Serial Port Connection ................................................................ 10

4.6 Commissioning ........................................................................... 10

Adjustments ................................................................................... 11

5.1 Adjustment With Rotary Switches ............................................... 11

5.2 Fast Adjustment To Nominal Output Range ................................ 13

5.3 eCal Electronic Adjustment Via xFace Software ......................... 13

5.4 Adjustment (eCal) With PLC ....................................................... 14

5.5 Testing the Scale Performance ................................................... 16

Setpoints ....................................................................................... 17

6.1 Setpoint Connection .................................................................... 17

6.2 Setpoint Adjustment ................................................................... 17

6.3 Adjustment To The Load On The Scale ...................................... 17

6.4 Adjustment By Measuring The Analog Output ............................. 17

Operation ....................................................................................... 18

Programming With xFace Software Over RS232 ........................... 19

8.1 Installation Of xFace Software .................................................... 19

8.2 Connection To The xFace Software ............................................ 19

Trouble Shooting ........................................................................... 21

Содержание FAA-27























Результаты поиска

Содержание FAA-27

Отзывы:

Похожие инструкции для FAA-27

Бренды по названию

Популярные бренды

Flintec FAA-27, Техническое руководство

Результаты поиска

Содержание FAA-27

Отзывы:

Похожие инструкции для FAA-27

Бренды по названию

Популярные бренды