Flexim FLUXUS G801 Скачать руководство пользователя страница 155

Страница: 155 / 177

18 Settings

FLUXUS G801

18.2 Measurement settings

155

UMFLUXUS_G801V1-0EN, 2020-06-26

18.2

Measurement settings

• Select the menu item

Measuring

• Press ENTER.

• Select

to activate the gas measurement,

off

to deactivate it.

• Press ENTER.

• Select

yes

if the measured sound speed is to be compared to the theoretical or expected value.

• Press ENTER.
The difference

c = c

mea

- c

stored

between the two sound speeds will be displayed in the lower line during the measurement.

stored

is the sound speed of the reference fluid stored in the database.

• Press

during the measurement to scroll to the display of

• Select a list item:

–

off

: profile correction 1.0

–

: profile correction 2.0 at ideal inflow conditions (default)

–

With disturbance

: profile correction 2.0 at non ideal inflow conditions

• Press ENTER.

• Select

normal

to display and transmit the profile corrected flow values, or

uncorr.

to display and output the flow

values without flow profile correction.

• Press ENTER.

An upper limit for the flow velocity can be entered.
• Enter zero to deactivate the flow velocity check.
• Press ENTER.

Special Funct.\SYSTEM settings\Measuring

Notice!

The settings will be stored at the end of the dialog. If the menu item is quit by pressing BRK, the changes will not be

stored.

Special Funct.\...\Measuring\Gas-Measuring

Special Funct.\...\Measuring\Compare c-fluid

Special Funct.\...\Measuring\ProfileCorr 2.0

Special Funct.\...\Measuring\Flow Velocity

Special Funct.\...\Measuring\Velocity limit

Содержание FLUXUS G801


















































































































































































Результаты поиска

Содержание FLUXUS G801

Отзывы:

Похожие инструкции для FLUXUS G801

Бренды по названию

Популярные бренды

Flexim FLUXUS G801, Руководство по эксплуатации

Результаты поиска

Содержание FLUXUS G801

Отзывы:

Похожие инструкции для FLUXUS G801

Бренды по названию

Популярные бренды