Flex L 15-10 150, Оригинальная инструкция по эксплуатации

Страница: 11 / 126

11
L 15-10 150 / L 21-6 230 / L 21-8 180 / L 24-6 230 / L 2100
Symbols used in this manual
Symbols on the power tool
For your safety
–
these operating instructions,
–
the ”General safety instructions” on the handling of power
tools in the enclosed booklet (leaflet-no.: 315.915),
–
the currently valid site rules and the regulations for the
prevention of accidents.
This angle grinder is state of the art and has been constructed
in accordance with the acknowledged safety regulations.
Nevertheless, when in use, the power tool may be a danger to
life and limb of the user or a third party, or the power tool or
other property may be damaged. The angle grinder may be
operated only if it is
–
as intended,
–
in perfect working order.
Faults which impair safety must be repaired immediately.
Intended use
This angle grinder
–
is designed for industrial applications,
–
for dry grinding and cutting metal and stone with rough
wheels and cutting-off wheels which are permitted to
operate at a circumferential speed of 80 m/s,
–
for surface grinding metal and stone with tapered cup
wheels up to 110 mm in diameter which are permitted to
operate at a circumferential speed of 50 m/s,
–
for surface grinding with sanding sheets on a backing pad
which has been designed to operate at the speed
of the machine,
–
for use with grinding tools and accessories which are
indicated in these instructions or recommended by the
manufacturer.
A special cutting guard must be used for cut-off grinding.
If stone is cut with fibre-reinforced cutting-off wheels, guide
supports must be used.
Not permitted are e.g. chain cutting wheels, saw blades.
The angle grinder is not suitable for polishing.
Safety Warnings for Angle Grinder
Safety Warnings Common for Grinding, Sanding or
Abrasive Cutting-Off Operations

This power tool is intended to function as a grinder, sand-
er or cut-off tool. Read all safety warnings, instructions, il-
lustrations and specifications provided with this power
tool. Failure to follow all instructions listed below may result in
electric shock, fire and/or serious injury.

Operations such as wire brushing or polishing are not
recommended to be performed with this power tool.
Operations for which the power tool was not designed may
create a hazard and cause personal injury.

Do not use accessories which are not specifically de-
signed and recommended by the tool manufacturer.
Just because the accessory can be attached to your power
tool, it does not assure safe operation.

The rated speed of the accessory must be at least
equal to the maximum speed marked on the power
tool. Accessories running faster than their rated speed can
break and fly apart.

The outside diameter and the thickness of your acces-
sory must be within the capacity rating of your power
tool. Incorrectly sized accessories cannot be adequately
guarded or controlled.

Threaded mounting of accessories must match the grind-
er spindle thread. For accessories mounted by flanges,
the arbour hole of the accessory must fit the locating di-
ameter of the flange. Accessories that do not match the
mounting hardware of the power tool will run out of balance,
vibrate excessively and may cause loss of control.

Do not use a damaged accessory. Before each use in-
spect the accessory such as abrasive wheels for chips
and cracks, backing pad for cracks, tear or excess
wear, wire brush for loose or cracked wires. If power
tool or accessory is dropped, inspect for damage or in-
stall an undamaged accessory. After inspecting and
installing an accessory, position yourself and bystand-
ers away from the plane of the rotating accessory and
run the power tool at maximum no-load speed for one
minute. Damaged accessories will normally break apart
during this test time.

Wear personal protective equipment. Depending on
application, use face shield, safety goggles or safety
glasses. As appropriate, wear dust mask, hearing pro-
tectors, gloves and workshop apron capable of stop-
ping small abrasive or workpiece fragments. The eye
protection must be capable of stopping flying debris gener-
ated by various operations. The dust mask or respirator
must be capable of filtrating particles generated by your op-
eration. Prolonged exposure to high intensity noise may
cause hearing loss.
WARNING!
Denotes impending danger.
Non-observance of this warning may result in death or
extremely severe injuries.
CAUTION!
Denotes a possibly dangerous situation.
Non-observance of this warning may result in slight injury or
damage to property.
NOTE
Denotes application tips and important information.
Before switching on the power tool, read the
operating manual!
Wear goggles!
Wear ear protection!
Protection class II (completely insulated)
Disposal information for the old machine
(see page 14)
WARNING!
Before using the angle grinder, please read and follow:
WARNING!
Read all safety warnings and all instructions. Failure to
follow the warnings and instructions may result in electric
shock, fire and/or serious injury. Save all warnings and
instructions for future reference.