manualshive.com logo in svg

Flavel RENOIR, Инструкция по установке и обслуживанию

Поделиться
Скачать
Flavel RENOIR Скачать руководство пользователя страница 8

1.8.3

Fitting to Pre-Cast Flue Installations.

The pre-cast opening must be a minimum of 122.7cm2 or

equivalent cross-sectional area and have a minimum effective flue

height of 3 metres. The flue spigot restrictor must be removed when

installing into pre-cast flue applications.

This appliance has been

tested for use in a pre-cast flue block complying with BS EN 1858.

In accordance with BS EN 1858, pre-cast flues built with directly

plastered faces (front or rear) are not correctly installed as to

ensure proper operation with any type of gas fire. In some

instances of this flue construction, temperature cracking of sur

face plaster may occur through no fault of the appliance. An air

gap or some form of insulation material should be installed to

prevent normal flue temperatures from damaging wall surfaces.

1.9

HEARTH FITTING

This appliance must only be installed on to a level concrete or non-

combustible hearth. The feet must not be removed when installing

directly onto a hearth.The hearth material must be a minimum thickness

of 13 mm with the top surface at least 50 mm above the floor level. The

hearth

must

be fitted symmetrically about the fire opening and have a

minimum width of 760 mm and a minimum projection of 300 mm

forwards from the fire opening.

1.10

SPILLAGE MONITORING SYSTEM

This appliance is fitted with an atmosphere sensing spillage monitoring

system in the form of an oxygen sensing pilot. This is designed to shut

the fire off in the event of partial or complete blockage of the flue

causing a build up of combustion products in the room in which the fire

is operating.

The following are important warnings relating to the

spillage monitoring system:

The spillage monitoring system must not be adjusted by the

Installer. The spillage monitoring system must not be put out of action.

When the spillage monitoring system is exchanged, only a complete

original Manufacturers part may be fitted. It is not possible to replace

individual parts on the pilot system on the appliance, only a complete

pilot assembly (including thermocouple) may be fitted.

8

Содержание RENOIR





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды