manualshive.com logo in svg

Flavel RENOIR, Инструкция по установке и обслуживанию

Поделиться
Скачать
Flavel RENOIR Скачать руководство пользователя страница 19

d)

Remove the valve retaining screws as shown below in Fig. 15

Fig. 15

d)

Remove the thermocouple, which is a push fit into the rear of the control

valve.

e)

Re-assemble in reverse order and carry out a gas tightness test.

4.4

REMOVING THE ODS- PILOT ASSEMBLY

Note : Because this appliance is fitted with an atmosphere sensing ODS-pilot

it is not possible to replace the thermocouple separately, because the

thermocouple position is factory set to a tight tolerance. Any replacement of

parts on the pilot requires a complete new pilot assembly.

a)

Remove the pilot retaining screws as described in section 4.2 d) &

fig. 14

b)

Disconnect the pipe pipe and push fit ignition lead

c)

Replacement new ODS in reverse order.

PARTS SHORTLIST

Replacement of any parts must be carried out by a competent person such as a CORGI registered gas

installer. The part numbers of the replaceable parts are as follows, these are available from specialist

spares stockists whose details can be found on our web site,www.bfm-europe.com, in the ‘stockist’ sec-

tion.

Coal set

FC-P085332

ODS Pilot

B-48360

Fuelbed

B-123570

Gas valve

B-63250

Rear Fibre board

B-65320

Glass Assy (Front)FC-A085705

19

2 off valve

retaining screws

Note : Prior to replacing the oxypilot on this product due to suspected

failure of the component, please remove all debris that has collected on

the lint guard of the oxypilot itself.

Содержание RENOIR





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды