background image

FTS 370i-2 IR

Revision A – 05/17/2019

15

Section 5 - Maintenance and Troubleshooting

5.1 Maintenance

No regularly scheduled maintenance is required for the beacon.

Flash Technology warranties the light output of the beacon to meet or exceed FAA/ICAO
requirements for a 5 year period. LED module replacement after 5 years is recommended
to ensure FAA/ICAO compliance. See Section 5.3.3.

Periodically check the GPS antenna for tightness.

Periodic cleaning of the lens is recommended with soapy water or any acrylic cleaning
solution. No other cleaning solutions are recommended. Abrasive compounds will scratch
the lens.

Optional mounting brackets should be checked periodically for tightness.

5.2 Troubleshooting

Follow the troubleshooting steps in the tables below as applicable. Beacon repair procedures are
provided in Section 5.3.

Table 5-1 – Troubleshooting - Beacon is in alarm

Step

Check/Test/Action

Action

1.a

Is beacon flashing at night?

Yes
No

Go to Step 1.b
Go to Step 2.a

1.b

Is beacon flashing in sync with other FTS 370i-2
beacons? Check beacon SYNC Status and
SYNC Alarm LEDs.

Yes
No

Go to Step 1.c
Go to Step 3

1.c

Is beacon PD Alarm LED on? Does beacon flash
in daytime?

Yes
No

Go to Step 4
Review sections 2.1, 3.1 and 3.2
to verify system operation.

Table 5-2 – Troubleshooting - Beacon does not flash at night

Step

Check/Test/Action

Action

2.a

Is AC power applied?
Measure at TB1 terminals L1 & L2.

Yes
No

Go to Step 2.b
Correct problem.

2.b

Is beacon PWR Status LED on?

Yes
No

Go to Step 2.c
Replace the Power Supply (See
Section 5.3.2)

2.c

Proceed to Step 2.d if there are no wires
connected at AUX+ and AUX-.

Disconnect the wires connected to AUX+ and
AUX-. Did normal operation resume?

Yes

No

Check operation/status of the
external control device.

Go to Step 2.d.

2.d

Is beacon MODE Status LED flashing?

Yes
No

Go to Step 2.e
Replace Controller Core PCB
(See Section 5.3.1)

2.e

Is beacon LED Alarm LED on?

Yes

No

Replace LED module (See
Section 5.3.5)
Replace Controller Core PCB
(See Section 5.3.1)

Содержание VANGUARD FTS 370i-2





























Отзывы: