FLARM FLARM V3+Mm Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 20

FLARM FLARM V3+Mm Скачать руководство пользователя страница 11

Manual external FLARM™ / PowerFLARM™ Display V3+Mm

External FLARM™/ PowrFLARM™

Display V3+Mm

with Software-version 3.7

Page

11

Start-up

The display is normally provided with power directly from the mainframe and operates with this source. The
V3+ display carries out a short self-test after receiving power and for a short time illustrates the software
version of the display; a LED-test follows and then the display is ready for use.

1. Switch on

2. Short internal functional test (not shown)

3. Display software version indication: Stand V 3.7
(the third position, the number “1” represents an
internal progressive numerical system and is not
shown)

4. LED-test – one by one and in groups all LED’s are switched on for a short time; this allows a visual test
to check if all indicators function correctly. (due to power consumption not all LED’s are illuminated
simultaneously, for this reason testing occurs in groups)

5. On the distance indicator a control symbol appears briefly for the adjusted measuring unit. The distance
depends on the adjusted configuration and is indicated in KM or NM – afterwards the measuring unit is no
longer visible.
Please ensure:

The distance indicator is given in KM:

-> There is no conversion of the given value
(symbol refers to European metric system)

The distance indicator is given in NM:
-> There is a conversion of the received metric value in
NM (symbol refers to “nn” of nautical miles)

6. In some mainframes the version number of the installed FLARM

TM

software version is briefly shown in

sequence three times (see Start-up 3.).

7. The display resp. the complete FLARM

TM

system is now ready for use. Normally only the Power LED

flashes and the GPS-LED blinks until the system orientates itself and defines its actual position.

NOTE: After installation an inspection must be made to ensure that the di and FLARM

TM

main device

do not interfere with any mechanical, electrical, electronic (radio) or magnetic (compass) system. This check
should be recorded in aircraft documents.

«
...
9
10
11
12
13
...
»

Содержание FLARM V3+Mm





















Отзывы:

Нет отзывов