background image

Manual FlexFiller Direct G4

12

7  Installation requirements

The FlexFiller Direct G4 is a wall mounted unit and should be installed at a suitable eye level, where 

the screen is easy to read and maintenance remains practical and possible. The wall of the set-up 

location for the FlexFiller Direct G4 must be such that stability is guaranteed and maintained.  

For general assembly instructions and commissioning steps of the product, see FlexFiller Direct G4 

Quick Start Guide in link below:

https://flamcogroup.com/manuals/flexfiller-direct 

All Flamco products should be installed by a Qualified Person with regard to the relevant 

requirements described in section 5.4: ''Staff qualification''. Check that the installation and other 

actions prior to use have been carried out in full (e.g. power supply available and connected, 

functioning or active fuses, seal tightness of the equipment). Any damage or loss incurred through 

incorrect commissioning by an unapproved engineer will not be covered by the warranty.

The following conditions must be met before starting the commissioning process. Failure 

to meet these conditions may result in injury or damage to the equipment, system and/

or property.

Conditions

1.

This equipment is designed to be installed in an indoor environment. The unit must be 

installed in a frost free environment, away from precipitation and water sprays/jets.

2. 

The heating/cooling system is fitted with an appropriate safety valve and expansion 

vessel.

3. 

Non-return valves, pressure reducing valves and RPZ valves must not be installed between 

the pressurisation unit and the heating/cooling system. These devices will prevent the 

pressure sensor from reading the system pressure.

4.

It is essential to have the pressurisation unit and the associated system expansion vessel 

connected to the system at the same point, to provide a neutral pressure reading. This 

point of connection should be in the system return header, on the suction side of the 

circulation pump.

5.

All necessary pipe/electrical connections have been made to a local standard.

6.

Refer to the appropriate datasheet for the maximum working pressure and temperature of 

the pressurisation unit. The conditions at the point of connection to the system must not 

exceed these values.

7.

The expansion vessel is pre-charged to the correct pressure (equal toFlexFiller Direct G4 

fill set-pressure))

It is advisable to fill the heating/cooling system prior to commissioning. If this is not 

possible, the FlexFiller Direct G4 can be used to fill the system after commissioning. 

Depending on the size of the system, this may take a considerable amount of time.
A mains cable is provided with the unit. A mains cable length of 1,5 meter may not be 

exceeded if replacement of a cable is necessary. 

Two WRAS approved flexible hoses with isolation valves are provided with the unit. It is 

essential for the maintenance of this unit to use hoses provided.

Содержание FlexFiller Direct G4





































Отзывы: