background image

Lit. No. 76454/76455/76456, Rev. 02 

July 15, 2018

SAFETY

SAFETY PRECAUTIONS

Improper installation and operation could cause 
personal injury and/or equipment and property 
damage. Read and understand labels and the 
Owner's Manual before installing, operating, or 
making adjustments.

 WARNING

•  Driver to keep bystanders minimum of 

25 feet away from operating spreader.

•  Before working with the spreader, secure all 

loose-

fi

 tting clothing and unrestrained hair.

•  Before operating the spreader, verify that all 

safety guards are in place.

•  Before servicing the spreader, wait for 

conveyor, auger, and spinner to stop.

•  Do not climb into or ride on spreader.

 CAUTION

If rear directional, CHMSL light, or brake 
stoplights are obstructed by the spreader, the 
lights shall be relocated, or auxiliary directional 
or brake stoplights shall be installed.

 WARNING

 

Overloading could result in an 

accident or damage. Do not exceed 
GVWR of UTV. See Loading section 
to determine maximum volumes of 

spreading material.

 CAUTION

Disconnect electric and/or hydraulic power 
and tag out if required before servicing or 
performing maintenance.

NOTE: Lubricate grease 

fi

 ttings after each use. 

Use a good quality multipurpose grease.

 CAUTION

 

DO NOT leave unused material in 
hopper. Material can freeze or solidify, 
causing unit to not work properly. 
Empty and clean after each use.

 CAUTION

•  Do not operate a spreader in need of 

maintenance.

•  Before operating the spreader, reassemble 

any parts or hardware removed for cleaning 
or adjusting.

•  Before operating the spreader, remove 

materials such as cleaning rags, brushes, 
and hand tools from the spreader.

•  Before operating the spreader, read the 

engine owner's manual, if so equipped.

•  While operating the spreader, use auxiliary 

warning lights, except when prohibited by law.

•  Tighten all fasteners according to the 

Torque Chart. Refer to Torque Chart for the 
recommended torque values.

 WARNING

Vehicles <10,000 lb GVWR: Obstructing 
the visibility from the vehicle's rear camera 
could result in serious injury or damage. An 
auxiliary camera system shall be installed 
if the vehicle's rear camera is removed or 
blocked.

Содержание POLY-CASTER 78601





















Отзывы: