background image

Lit. No. 94197, Rev. 05 

 

November 1, 2010

Copyright © 2010 Douglas Dynamics, L.L.C. All rights reserved. This material may not be reproduced or copied, in whole or in part, in any 
printed, mechanical, electronic, 

fi

 lm or other distribution and storage media, without the written consent of Fisher Engineering. Authorization 

to photocopy items for internal or personal use by Fisher Engineering outlets or spreader owner is granted.

Fisher Engineering reserves the right under its product improvement policy to change construction or design details and furnish equipment 
when so altered without reference to illustrations or speci

fi

 cations used. Fisher Engineering or the vehicle manufacturer may require or 

recommend optional equipment for spreaders. Do not exceed vehicle ratings with a spreader. This product is manufactured under the 
following U.S. patent: 7,400,058. Fisher Engineering offers a limited warranty for all spreaders and accessories. See separately printed 
page for this important information. The following are registered (

®

) or unregistered (™) trademarks of Douglas Dynamics, L.L.C.: FISHER

®

POLY-CASTER™.

Printed in U.S.A.

  A SUBSIDIARY OF DOUGLAS DYNAMICS, L.L.C.

Fisher Engineering
50 Gordon Drive
Rockland, ME  04841-2139
www.

fi

 sherplows.com

Содержание POLY-CASTER 78001

























Отзывы: