background image

BATTERY CARE

•  If a battery leak develops,

 avoid contact with the leaking 

acid and place the damaged battery in a plastic bag. See 
next section for proper disposal.

•  If acid comes in contact with skin or eyes, 

flush with cool 

water for at least 15 minutes and call a physician.

•  If acid is internally ingested,

 give water, milk of magnesia 

or egg whites immediately. Never give emetics or induce 
vomiting. Call a physician.

•  Do not allow the battery to run down completely 

before charging.

•  Charge the battery before storing the vehicle, and at least 

once per month, even if the vehicle has not been used.

•  Charge the battery after each use, regardless of how long 

the vehicle was used.

•  Leaving the battery in a discharged condition will ruin it.
•  Always remove an exhausted battery from the vehicle. 

Battery leakage and corrosion can damage the vehicle.

•  Do not store the battery in temperatures above 24° C or 

below -23° C.

BATTERY DISPOSAL

•  Your Power Wheels

®

 battery is a non-spillable sealed 

lead-acid battery. It must be recycled or disposed of in an 
environmentally sound manner.

•  Do not dispose of a lead-acid battery in a fire. The battery 

may explode or leak.

•  Do not dispose of a lead-acid battery in your regular, 

household trash. The incineration, landfilling or mixing of 
sealed lead-acid batteries with household trash is prohibited 
by law in most areas.

•  Return an exhausted battery to a federal or state approved 

lead-acid battery recycler, such as a local seller of 
automotive batteries. Contact your local waste management 
officials for other information regarding the environmentally 
sound collection, recycling and disposal of lead-acid batteries.

•  Protect the environment by not disposing of this product with 

household waste (2002/96/EC). Check your local authority 
for recycling advice and facilities

BATTERY CARE AND DISPOSAL

VEHICLE CARE

CONSUMER INFORMATION

•  Check all screws, cap nuts and their protective 

coverings regularly and tighten as required. Check plastic 
parts on a regular basis for cracks or broken pieces.

•  During snowy or rainy weather, the vehicle should be stored 

inside or under a protective cover. Remember to charge the 
battery at least once per month while your vehicle is not in 
regular use.

•  Avoid operating the vehicle in wet or snowy conditions, 

and do not spray the vehicle with a hose. Do not wash 
the vehicle with soap and water. Water or moisture in the 
motors or electrical switches can cause them to corrode, 
and could cause switch or motor failure.

•  Avoid operating the vehicle on sand, loose dirt or gravel. 

Sand, loose dirt or gravel in the motors or electrical 
switches can cause them to jam, and could cause switch or 
motor failure.

•  The vehicle can be wiped down with a soft, dry cloth. 

For a shiny finish, you can wipe plastic parts with 
a non-wax furniture polish applied to a soft-cloth. Do not 
use automotive wax. Do not use soap and water or spray 
the vehicle with a hose.

AUSTRALIA:

 

Mattel Australia Pty. Ltd., 658 Church Street, 

Locked Bag #870, Richmond, Victoria 3121 Australia. 
Consumer Advisory Service 1300 135 312.

NEW ZEALAND:

 

16-18 William Pickering Drive, Albany 1331, 

Auckland.

•  Before first-time use, you must charge the battery 18 hours!

•  Charge the battery immediately after each use. Charge the 

battery once a month, even if the vehicle is not used or stored.

•  Visit us online for our Troubleshooting Guide - 

service.fisher-price.com

PRINTED IN MEXICO 

Y2189pr-0729

©2012 Mattel. All Rights Reserved. Tous droits réservés.

Содержание Power Wheels Y2189





















Отзывы: