manualshive.com logo in svg

Fisher & Paykel GWL08US, Руководство по обслуживанию

Поделиться
Скачать
Fisher & Paykel GWL08US Скачать руководство пользователя страница 6

6

DIAGNOSTIC MODE  cont:
The following tests can be carried out in the diagnostic mode.

3.2  LID SWITCH & OUT OF BALANCE SWITCH TEST

Press the 

SPIN SPEED UP

 button until the 

MEDIUM SPIN

 LED is on, (binary count 4).

When the Lid is open the 12 minute wash LED will be on.

Activating the Out of Balance lever under the top deck will cause the 6 minute LED to turn on.  The
Out of Balance lever can be activated by moving the inner basket towards the right hand corner of
the cabinet.  It will take up to 1 second for the LED to respond after the Out of Balance has been
activated.
Also when in this mode with the 

MEDIUM SPIN SPEED

 LED on, the 

SPIN LED

 will display the

SIZE SETTING

.

SPIN LED on = MODEL GWL08

3.3  DRAIN PUMP TEST

The 

REGULAR CYCLE

 button turns the drain pump on or off.  The 

REGULAR LED

 will turn

on when the pump is on.  This feature can be used to drain the tub.

3.4  WATER VALVE TEST

Press the 

WASH TEMPERATURE DOWN

 button to turn the Cold Water Valve on.  The Cold

Water LED will also turn on.

Press the 

WASH TEMPERATURE UP

 button to turn the Hot Valve on.  The Hot Water LED will

also turn on.

NOTE:

The drain pump test, water valve test, restart and recycle features can be used on any level in the
diagnostic mode.

Содержание GWL08US





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды