manualshive.com logo in svg

Fisher & Paykel GWL08US, Руководство по обслуживанию

Поделиться
Скачать
Fisher & Paykel GWL08US Скачать руководство пользователя страница 16

16

50.

(00110010) Hot Valve Faulty

The Motor Controller Module has measured a voltage from the valve diagnostic circuit that
indicates that the hot valve is faulty.  The most likely cause is that the valve harness has not been
connected correctly or the valves are open circuit.  See fault 48 for service procedure.

53.

(00110011) Rotor Position Sensor Step Fail

The Motor Controller Module has attempted a motor step test and has found that the motor has not
stepped in the correct direction.  It has detected that the motor is connected and that the motor drive
is operational.  The rotor position sensing system is at fault.

Primary Source

 - Wiring.

Action

 - Check the Rotor Position Harness for continuity and that the connectors are correctly to

the Rotor Position Sensor and the Motor Controller.

Secondary Source

 - Rotor Position Sensor.

Action

 - Check the Rotor Position Sensor patterns with a RPS Tester, if faulty fit a new Rotor

Position Sensor.

Tertiary Source

 - Motor Controller Module.

Action 

- Replace the Motor Controller Module.

54.

(00110110) Motor/Motor Controller Module Step Fail

The Motor Controller Module has attempted a motor step test and has found that the motor has not
stepped in the correct position.  The Motor Controller Module has detected that there is no current.
This indicates that either the motor is not connected or the Motor Controller Module motor drive is
faulty.

Primary Source

 - Wiring.

Action

 - Check the continuity of the motor harness and that the connectors are correctly

 

applied to

the motor and Motor Controller Module.

Secondary Source 

- Motor

Action

 - Check continuity of motor phases.  Check the bridge terminal on the stator is not open

circuit.  Replace the stator.

Tertiary Source

 - Motor Controller Module.

Action

 - Replace Motor Controller Module.

56.

(00111000) Basket Check No Valid Fault

While carrying out a basket check, the machine has not been able to determine a valid basket status
and so the Display flags this fault. This fault differs from fault 40 in that a valid basket status could
not be determined.

Primary Source:

   Loading.

Action:

   Remove items until the remaining ones can move freely, or rearrange the load so that the

clothes are evenly distributed around the basket, or select a higher water level.  If the load was to
one side of the basket or too heavy it can be possible for the agitator to bind in one direction when
trying to sense basket float.

Secondary Source:  

Mechanical.

Action:

1.

Check the machine is not syphoning.

Содержание GWL08US





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды