Fisher & Paykel AeroCare Скачать руководство пользователя страница 55

Страница: 55 / 88

AeroCare controls

Keylock

Keylock can be used to deactivate the buttons on your AeroCare dryer when it is in use. This
will avoid accidental button touches from items left on top of the dryer (eg washing baskets,
clothing) as well as touches from any little fingers.

To turn Keylock ON or OFF:

■

Touch and hold the KEYLOCK button for two seconds.
Note: when activated, the light above the KEYLOCK button is illuminated.

If Keylock is activated:

■

To turn your dryer on,

touch

and hold the POWER button for two seconds.

This will activate the

control panel. Keylock will remain activated but let you select your drying cycle options and start
the cycle.

■

To PAUSE your dryer at any time during the cycle,

touch and hold the START/PAUSE button for

two seconds.

■

To STOP your dryer and power off, simply touch the POWER button.

Содержание AeroCare

























































































Результаты поиска

Содержание AeroCare

Отзывы:

Похожие инструкции для AeroCare

Бренды по названию

Популярные бренды

Fisher & Paykel AeroCare, Инструкция по установке и эксплуатации

Результаты поиска

Содержание AeroCare

Отзывы:

Похожие инструкции для AeroCare

Бренды по названию

Популярные бренды