Fisher & Paykel AeroCare Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 88

background image

Installation instructions

24

Connecting the dryer using 3-wire connection

Important!

■

■

DO NOT use in Canada.

■

■

DO NOT use for Mobile home installations, on new constructions, or on recreational vehicles.

■

■

NOT for use in areas where local codes prohibit grounding through the neutral conduction.

Ground strap

If required by local codes, install an external ground (not provided) to grounded metal,
a cold water pipe or other established ground as determined by a qualified electrician.

Hot wire

Strain relief bracket

3/4” (19 mm), UL recognized strain relief

120/240V 30 amp power supply cord kit (min
length 4 feet (1.5 m)) marked for use with
dryers and provided with closed loop or spade
terminals with upturned ends (not supplied)

Fuse

Cover

Screw

Neutral (white)

Screws (2)

Fig.15 3-wire connections

Hot wire

Green ground screw

1

Turn off the circuit breaker(s) (30 amp) or remove the dryer’s circuit fuse at the electrical box.

2

Ensure the dryer cord is unplugged from the wall outlet.

3

Locate and remove the power cord cover at the lower rear of the dryer.

4

Install a ¾” (19 mm) UL-recognized strain relief to the entry hole for the power cord. Move the

power cord through the strain relief.

5

Connect the power cord according to the following:

a

Connect the two hot lines to the outer screws of the terminal block (labelled L1 and L2).

b

Connect the neutral (white) line to the center of the terminal block (labelled N).

6

Ensure the ground strap is connected to neutral (center) terminal of block, and to the green

ground screw on located on the cabinet rear.

7

Tighten all three terminal block screws completely.

8

Correctly secure the power cord to the strain relief.

9

Replace the power cord cover.

WARNING!

NEVER leave the power cord cover off the terminal block.

«
...
24
25
26
27
28
...
»

Содержание AeroCare

























































































Отзывы:

Нет отзывов

Похожие инструкции для AeroCare

Бренд: Zanussi Electrolux Страницы: 29

Бренд: Cosori Страницы: 23

Бренд: Thermo Scientific Страницы: 45

Бренд: KAI Страницы: 13

Omk.FRT01.E11.0060.Z5F

Бренд: omake Страницы: 57

Бренд: Ultrean Страницы: 12

Бренд: Aike Страницы: 4

Бренд: Maytag Страницы: 28

Бренд: Linsar Страницы: 12

Бренд: Maytag Страницы: 72

Бренд: Imesa Страницы: 28

Бренд: GE Страницы: 32

Бренд: GE Страницы: 40

Бренд: GE Страницы: 128

Бренд: GE Страницы: 16

Бренд: Mediclinics Страницы: 65

Бренд: Electrolux Страницы: 44

Бренд: Electrolux Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды