Step
Action
3.
Enhanced Sequential Mode - Press *83, then follow the prompts as follows:
A 01
a. Zone Number - Enter 2-digit zone number of the first transmitter to have its serial number
entered. The system will announce the Voice Descriptor for the selected zone number, if it is
programmed.
Press [*] to continue. Starting with this zone, the system will search for the first transmitter,
which has all of the following attributes pre-programmed in Zone Programming.
1) The correct input type selected in *56 (RF, UR, or BR programmed)
2) The correct loop number selected in *56
3) No serial number programmed
4) Zone type
Notes:
1. If the first zone number entered does
not
have one or more of the above attributes, the system will
search its database for the first zone that does, and will display it at the ENROLL SERIAL NUMBER
prompt (1b).
2. Pressing 00 exits mode, upon which the prompt “83” blinks, indicating the mode is inactive.
1A
zz
b. Enroll Mode -
If “
L
” is displayed, the serial number for this transmitter has already been entered,
however, it may still be confirmed, viewed or deleted.
1) If the transmitter’s serial number has not been previously entered, enter the enroll serial
number mode now by pressing “1”, or copy the last serial number that was entered by
pressing “2”.
1A
LC
2) If the transmitter’s serial number has been previously entered, it may be viewed by pressing
“3” or deleted by pressing “9”.
Note:
If view is selected; each digit will be re-displayed, and the keypad will beep once for digits 1-6, and three
times for the last digit.
3) Once the serial number has been entered the system will return to the (1A) prompt and “
L
”
will be displayed.
Note:
This point can be faulted and restored and the panel will listen for the transmission.
4) The serial number/loop number combination that was entered can be confirmed by faulting
and restoring the zone being entered. If the panel receives a transmission that matches the
serial number and loop number entered, the keypad will beep three times, and “C” will be
displayed. This indicates that the serial number transmission has been confirmed to match.
No further transmissions will be received.
Note:
When confirming a 4-button key, it assumed that all loops are used and only the serial number is
confirmed. Pressing any key will allow a confirm. Two beeps indicate that the template has been
accepted. A single long beep indicates illegal entries, or duplicate serial number/loop entry.
5) When the last zone has been entered, the display will remain on that zone. To exit this mode
and return to data field program mode, press 00 at the ZONE NUMBER prompt
6) Once all zones have been programmed, test each zone using the system’s Test mode. Do
not use the Transmitter ID Sniffer mode for this, since it will only check for transmission of
one zone on a particular transmitter, and not the zones assigned to each additional loop.
1
b
zz
c. Serial Number - This prompt can be used to enroll the transmitter serial number via RF
transmission or manually. If using RF Learning proceed to c. 1). If using the manual mode skip to
c. 2).
1)
RF Learning -
Two (2) transmissions (two key depressions at least five second apart) will be
required for BR type or four (4) transmissions (fault, restore and fault, restore) for UR or RF
type. BR type devices can be enrolled only by transmission from BR devices. Likewise, UR
and RF devices can only be enrolled by transmission from a UR or RF device.
If the learned serial number has a different loop number than that entered in *56 the system
will announce the Voice Descriptor, if it is programmed, followed by two beeps and
will return
to Prompt (1A) and “L” will be displayed.
If the loop number captured by RF transmission and that entered in *56 mode match, the
system will announce the Voice Descriptor, if it is programmed, followed by three beeps and
return to Prompt (1A) and “LC” will be displayed. No additional transmissions are needed for
confirmation.
Note:
BR type devices can be enrolled only by transmission from BR devices. Likewise, UR and RF devices
can only be enrolled by transmission from a UR or RF device.
1
b
2) Manual Entry -
Enter the 7-digit serial number printed on the transmitter. If you enter an
incorrect digit, press the [#] key to backup to prompt (1A) and start over. When all seven
digits are entered press the [*] key.
- 4 -
