background image

 

- 2 -

 

WIRING TABLE 

Keypad

 

Control Panel

 

Wire Color 

G

 

Data In

 

Green 

 

 Aux Pwr (GND)

 

Black 

+

 

+ Aux Pwr

 

Red 

Y

 

Data Out

 

Yellow 

Note: 

NO (normally Open) and C (common) are the 

connections for the relay output 

+

FA270RF-005-V0

NO C

Y

G

 

Figure 2 - FA270RF Wiring Connections

 

 

APPLICATION GUIDELINES  

Use the following guidelines when planning an installation: 

 

Local wireless keys (wireless keys programmed directly into the FA270RF) may be used regardless of whether the 
RF receiver in the FA270RF is enabled or disabled. 

 

If using bi-directional devices, be sure to enable the transmitter module in the FA270RF. 

 

If transmitters are programmed into the control panel, be sure to enable the receiver. (Make sure you do not 
exceed the number of receivers supported by the control panel.) 

 

If a local wireless key is programmed to arm/disarm or to trigger a relay on the control panel, a user code must be 
entered into the FA270RF. This user code must also be programmed into the control panel. 

 

You must set the House ID in the FA270RF (If the House ID source is “System”, the FA270RF uses the House ID 
programmed in the Control Panel.) only if you are using RF keypads and/or bi-directional devices; 

AND

 the House 

ID Source is the FA270RF (Local).

 

FA270RF Application Guide 

The following guide outlines how to program the wireless keys, RF receiver, and the House ID in the FA270RF for 
your installation. 

*  Two FA270RFs are needed for this application: one assigned to partition 1 and one assigned to partition 2. 

**  If using an RF keypad on only one partition, the FA270RF’s partition assignment in panel programming must match the partition. 

*** If set for Local on a partition control, the FA270RF’s partition assignment must match the one programmed in the BD device.

 

Are you using

 

FA270RF Programming Options 

System Control Panel

 

RF keys 

beyond 

system’s 

capacity?

 

RF receivers 

beyond 

system’s 

capacity?

 

RF keypads and/or 

Bi-directional 

devices on more 

than 1 partition?

 

Program 

Wireless Keys 

Into

 

Receiver 

Enable

 

House ID 

Source

***

 

FA110C, FA120C

 

N/A

 

N/A

 

N/A

 

FA270RF

 

OFF 

 

Local [0] 

NO

 

NO

 

N/A

 

System

 

ON [1]

 

System [1] 

YES

 

NO

 

N/A

 

FA270RF

 

ON [1]

 

System [1] 

FA142C, FA148C, FA148CP

 

YES

 

YES

 

N/A

 

FA270RF

 

OFF [0]

 

Local [0] 

NO

 

NO

 

NO

 

System

 

ON [1]

 

System [1] 

YES

 

NO

 

NO

 

FA270RF

 

ON [1]

 

System [1] 

YES

 

YES

 

NO

 

FA270RF

 

OFF [0]

 

Local [0] 

NO

 

YES

 

YES*

 

System

 

OFF [0]

 

Local [0] 

FA162C, FA168C, FA168CPS

 

YES

 

YES

 

YES*

 

FA270RF

 

OFF [0]

 

Local [0] 

NO

 

NO

 

NO**

 

System

 

ON [1]

 

System [1] 

YES

 

NO

 

NO**

 

FA270RF

 

ON [1]

 

System [1] 

YES

 

YES

 

NO**

 

FA270RF

 

OFF [0]

 

Local [0] 

NO

 

YES

 

YES

 

System

 

OFF [0]

 

Local [0] 

FA1220CV, FA1340C

 

YES

 

YES

 

YES

 

FA270RF

 

OFF [0]

 

Local [0] 

Содержание FA270RF









Отзывы: