background image

8

Wire the EC485 converter to the E340 controls in the following manner:

FIGURE 9: 

For complete details on wiring and communicating with the E340 controls refer to bulletin BW-1000
(BoilerWorx™ Communication Software Program).

NOTICE

When Fireye products are combined with equipment manufactured by others and/or integrated into
systems designed or manufactured by others, the Fireye warranty, as stated in its General Terms and
Conditions of Sale, pertains only to the Fireye products and not to any other equipment or to the
combined system or its overall performance.

WARRANTIES

FIREYE guarantees for 

one year from the date of installation or 18 months from date of manufacture

of its products to replace, or, at its option, to repair any product or part thereof (except lamps, elec-
tronic tubes and photocells) which is found defective in material or workmanship or which otherwise
fails to conform to the description of the product on the face of its sales order. 

THE FOREGOING

IS IN LIEU OF ALL OTHER WARRANTIES AND FIREYE MAKES NO WARRANTY OF
MERCHANTABILITY OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED.

 Except as

specifically stated in these general terms and conditions of sale, remedies with respect to any product
or part number manufactured or sold by Fireye shall be limited exclusively to the right to replace-
ment or repair as above provided. In no event shall Fireye be liable for consequential or special dam-
ages of any nature which may arise in connection with such product or part.

FR. GRD

SHLD

TD (A)

TD (B)

RD (A)

RD (B)

+12VDC

GND

ECHO

ON

OFF

RTS

SD

CONTROL

ED612

120VAC
50/60Hz

COMMUNICATION TERMINATOR

ON LAST E340 CONTROL

(COM B) TERMINAL 80

(COM A) TERMINAL 81

TO E340 CONTROLS

(COM B) TERMINAL 80

(COM A) TERMINAL 81

DATA COMMUNICATION LINK

DB25 CONNECTOR
TO COMPUTER’S
RS232 SERIAL 
COMMUNICATION
PORT

NOTE:

1. ECHO OFF

2. RTS

WHITE STRIPE
TO +12VDC

EC485 CONVERTER

Note: The two jumpers on the 485CON converter should be set to “RTS” and “Echo Off.”
Note: TD (A) and RD (A) on EC485 converter connected to Terminal 80 (COM B) of E340 control.

TD (B) and RD (B) on EC485 converter connected to Terminal 81 (COM A) of E340 control.

61-6689

(USUALLY NOT REQUIRED)

FIREYE 

E-8002 

3 Manchester Road

MARCH 27, 2015

Derry, New Hampshire 03038 USA

Supersedes April 3, 2013

www.Fireye.com

Содержание 129-145-1









Отзывы: