Firenzo DECO RURAL SD Скачать руководство пользователя страница 17

Deco RU SD & Plaza RU SD Installation 

 

 
 

17 

 

5.  ASSEMBLY INSTRUCTIONS 

 

Carefully remove all packaging. 

 
2a 

If installation is into a 

MASONRY ENCLOSURE

: Remove firebricks as necessary to fit 

the firebox into the opening. The firebox front when installed must be flush with the 
finished fireplace surround and on a level base of the same height as the finished floor 
protector.  This may be achieved by using a concrete mix to level the base. 

 
2b 

If installation is into a 

BUILT-IN CANOPY

: Construct the canopy box as per page 7 

and install into framework following guides on pages 8-14 as applicable. 

 

Slide the firebox into the opening so that the outer casing return folds are flush 

 

with the finished fire surround. 

 

DUE TO NEW ZEALAND BEING AN EARTHQUAKE PRONE COUNTRY, IT IS 
IMPORTANT TO ANCHOR THE INSERT DOWN IN CASE OF EARTH 
MOVEMENT.  See diagram page 20 showing Typical Insert Installation. 

 

Install Flue as per instructions on page 18 and 19 if installing in a masonry fireplace or 
page 8,9,10,11,12, 15 if using a Built-in fire canopy (zero clearance box). 

 

Now that the firebox and flue are in position, 

place 25mm white kaowool blanket

 

(supplied) on top of casing

 

As this fire sources its combustion air from the chimney cavity/enclosure, the fire MUST 
be sealed around the front between the casing and the masonry or inbuilt canopy.  This is 
achieved by packing the yellow ISB insulation supplied between the casing and the 
masonry or inbuilt canopy at the FRONT ONLY to maximum depth of 90mm.   

 
 

UNDER NO CIRCUMSTANCES SHOULD THE AIRPORTS ON THE SIDE 
OF THE HEATER BE RESTRICTED.  Refer diagram page 20. 

 
 

The fire sources its combustion air from the chimney cavity, not from the room 
where the fire is installed.  This ventilation air should be drawn down the 
chimney cavity from the air gap set up when the top spacer bracket holds the 
weather collar off from the outer flue casing enabling air to be drawn into the 
chimney cavity.  Failure to ensure this air supply will starve the fire of air and 
lead to poor performance. 

 

Assemble and fit the fascia as per instructions on page 21. 

 

 
NOTE:  In the case of some insert fires into existing masonry fireplaces it may be necessary to 

install additional adventitious ventilation into the chimney cavity as per AS/NZ 2918 
3.4.1.2 to assist air flow into the fire..  This ventilation should not be taken/drawn from 
the room that the fire is installed in. 

 
 
 
 

Содержание DECO RURAL SD























Отзывы: