background image

Page 31/43 

 
 
 
 

 

 

 

 

Firemiks AB 

Instruction manual version: SPFA FM 

P.O. Box 8155, 104 20 STOCKHOLM, Sweden 

  

phone +46-8-551 196 10 - [email protected] - www.firemiks.com 

7.3  Once a month 

 

7.3.1  Check there are no leakages on the unit or in the connections or couplings 

and that no fasteners on the unit and installation are loose. 

7.3.2  Check the oil level in the concentrate pump. Use the dip stick or the oil level 

window if available on your unit. Refill if necessary according to section 7.6.1 

7.3.3  Dry pipe system. Rotate the water motor and the concentrate pump manually. 

Remove the protection cap on the back gable and use a wrench to turn the 
water motor rotor. Note! Do not forget to put back the protection cap. 

If 

initially there is much resistance to rotation which releases once there 
is movement, increase the rotating interval to once every second week. 
With salt water, rotation must also be done at least every second week.

 

 

 

 

7.3.4  Wet pipe system. Let a small water flow go through the unit for about 30 

seconds (see also 4.3.13) and check rotation of the unit. 

If initially there is 

much resistance to rotation which releases suddenly, increase the 
rotating interval to once every second week. With salt water, rotation 
must also be done at least every second week or more often if 
necessary

 

 

 

Содержание 1200-3-PP-F-ALU-FM












































Отзывы: