Fiplex DH7 Series Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 42

background image

UM-0821

33



Date  and  Time:  page  to  modify  real  time  clock.  When  the  Signal  Booster  is  not
powered,  this  clock  runs  with  a  voltage  supply  provided  by  a  3V  lithium  battery,
button  type  of  20mm  (CR2032)  with  220mA·h.  This  suffices  for  at  least  half  year.
When  the  Signal  Booster  is  powered,  no  current  is  drained  from  the  battery.  So,
actual  battery  life  will  depend  on  Signal  Booster  usage.  For  battery  replacement,
please locate battery holder between USB and Ethernet connectors on main board.
Battery positive side is UP, i.e. on holder clip.

After clicking on “Apply Changes” link, next message will appear, warning the user that
system needs to be rebooted.

«
...
36
37
38
39
40
...
»

Содержание DH7 Series











































Отзывы:

Нет отзывов

Похожие инструкции для DH7 Series

Бренд: Oster Страницы: 32

Бренд: Korona Страницы: 20

Бренд: TP-Link Страницы: 2

zBoost z-Force YX240

Бренд: Wi-Ex Страницы: 2

Бренд: Extreme USB Страницы: 2

Бренд: BZB Gear Страницы: 10

TributeCollection JB 3010

Бренд: Braun Страницы: 14

Бренд: BlueSpot Страницы: 4

Бренд: NETGEAR Страницы: 27

Бренд: Wilson Electronics Страницы: 20

Drive Reach Fleet

Бренд: weBoost Страницы: 16

Бренд: SIIG Страницы: 2

Бренд: G&K Страницы: 4

Бренд: XtendLan Страницы: 3

EXT-HDMIIR-CAT5

Бренд: Gefen Страницы: 18

Бренд: Link Страницы: 23

Бренд: CableTronix Страницы: 14

Бренд: cable matters Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды