Fiplex DH7 Series Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 42

background image

UM-0821

III

About this manual

This manual describes installation, commissioning, operation and maintenance of Fiplex

DH7 Series Digital Signal

Booster, and

Fiplex Control Software (FCS)

. The first part of the manual describes the Signal Booster hardware and the

second part describes the software.

Hardware and software mentioned in this manual are subjected to continuous development and improvement. Consequently,
there may be minor discrepancies between the information in this manual and the performance and design of the hardware
and software. Specifications, dimensions and other statements mentioned in this manual are subject to change without
notice.

This manual or parts of it may not be reproduced without the written permission of Fiplex Communications Inc.

Infringements will be prosecuted. All rights reserved.

Copyright © Fiplex USA, Miami, 2015.

«
1
2
3
4
5
...
»

Содержание DH7 Series











































Отзывы:

Нет отзывов

Похожие инструкции для DH7 Series

Бренд: Argos Страницы: 11

Бренд: Zwilling Страницы: 56

Бренд: NTI Страницы: 5

Бренд: Patton Страницы: 70

SecureMesh XTEN-1000

Бренд: Trilliant Страницы: 21

Бренд: Bamix Страницы: 44

Component Video/Digital Audio CAT5 Extender

Бренд: Cables Forless Страницы: 2

Бренд: DCU Tecnologic Страницы: 2

Бренд: Abocom Страницы: 2

Бренд: StarTech.com Страницы: 8

Бренд: Hotpoint Страницы: 12

SIGNAL BOOSTER - WARRANTY

Бренд: Motorola Страницы: 2

STARLINE SLE Series

Бренд: Motorola Страницы: 48

Бренд: Silvercrest Страницы: 19

Бренд: Silvercrest Страницы: 34

Бренд: Silvercrest Страницы: 40

Бренд: Silvercrest Страницы: 24

Бренд: Silvercrest Страницы: 58

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды