Fike ECS Series Скачать руководство пользователя | Manualshive

Страница: 55 / 66

background image

ECS Series Manual —

P/N LS10262-001FK-E:A 3/3/2021

55

Installing the FIK-DUAL50W

Device Installation

4.7.8 Setting the FIK-DUAL50W Mode

Figure 4.52 DIP Switch Modes

When the FIK-DUAL50W is connected to an FCP-300ECS or FCP-2100ECS, the mode is set using the HFSS Programming Tool and the
DIP switch mode selector is ignored.

The amplifier modes are as follows:

•

50 Watt with Backup - Amp A powers Audio Circuits 1 - 8. Amp A is backed up by on-board Amp B. (Default, DIP setting at 2).

•

100 Watt with no Backup - Amp A powers Audio Circuits 1 - 4. Amp B powers Audio Circuits 5 - 8. There is no backup. (DIP setting
at 1).

•

100 Watt with Backup (requires FIK-50WBU) - Amp A powers Audio Circuits 1 - 4. Amp B powers Audio Circuits 5 - 8. The FIK-
50WBU will backup Amp A or Amp B but never both. (DIP setting at 3).

If the FIK-DUAL50W is connected to an FCP-2100ECS system and configured to operate in a dual channel setup, Amp A and/or Amp B is
not restricted to which audio circuits it can power. However, both can never power the same audio circuit.

4.7.9 Test Switch use

SW1 - AMP A

Switch should be moved to the “ON” position for normal operation. Move this switch to the “Test” position to test backup amplifier.

SW2 - AMP B

Switch should be moved to the “ON” position for normal operation. Move this switch to the “Test” position to test backup amplifier.

NOTE:

Please allow up to 3 minutes for backup amplifier to engage.

4.7.10 Connecting AC Power

At installation, connect the AC terminals to the power source as shown in Figure 4.53. It may be necessary for a professional electrician to
make this connection.

The AC terminals are rated as 120VAC, 60 Hz or 240VAC, 50/60 Hz.

Figure 4.53 AC Connection

«
...
53
54
55
56
57
...
»

Содержание ECS Series



































































Отзывы:

Нет отзывов

Похожие инструкции для ECS Series

Бренд: 2N Страницы: 23

AirGENIO SUPERIOR

Бренд: 2VV Страницы: 27

Бренд: 2N Страницы: 91

Бренд: bar Страницы: 2

Бренд: DayTronic Страницы: 414

Бренд: JBL Страницы: 16

Authentics L 16

Бренд: JBL Страницы: 17

RDS17S-ELITE1-R1

Бренд: D&R ELECTRONICS Страницы: 12

Бренд: IBCcontrol Страницы: 16

Бренд: Fagor Страницы: 68

WEB’LOG RESIDENTIAL

Бренд: Meteo Control Страницы: 4

Бренд: Jaycar Страницы: 8

Бренд: Magnavox Страницы: 25

Бренд: Yealink Страницы: 36

Бренд: Vitek Страницы: 28

Бренд: welldana Страницы: 7

Бренд: Technics Страницы: 14

Бренд: Forge Electronics Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды