Fike ECS Series Скачать руководство пользователя | Manualshive

Страница: 22 / 66

background image

22

ECS Series Manual —

P/N LS10262-001FK-E:A 3/3/2021

Device Installation

Installing the FIK-NVCM

4.

Install the FIK-SW24 on the six mounting studs located on the inside of the dead front panel. See Figure 4.4 for FCP-300ECS or
Figure 4.6 for FCP-2100ECS.

5.

For the FCP-300ECS, connect one end of the wiring harness (P/N 130398 supplied) to the FIK-EMG and the other end to the FIK-
SW24 as shown in Figure 4.5.

6.

For the FCP-2100ECS, connect one end of the wiring harness (PN 130398 supplied) to the FIK-EMG and the other end to the P4
connector on the FIK-NVCM as shown in Figure 4.6. If two FIK-SW24's are used, connect one FIK-SW24 to the other FIK-SW24 as
shown in Figure 4.7.

7.

Secure the switch expander(s) to the dead front panel using the supplied six ¼” Hex nuts.

8.

Restore AC power.

9.

Reconnect backup batteries

Figure 4.4 Wiring Harness Connection for the FIK-NVCM to the FCP-300ECS

Figure 4.5 Connection between the FIK-EMG and One FIK-SW24

FACP

NVCM

«
...
20
21
22
23
24
...
»

Содержание ECS Series



































































Отзывы:

Нет отзывов

Похожие инструкции для ECS Series

Бренд: Bang & Olufsen Страницы: 20

Бренд: Bang & Olufsen Страницы: 24

BeoSound Ouverture

Бренд: Bang & Olufsen Страницы: 44

AZ8350 - Cd Radio Cass Recorder

Бренд: Magnavox Страницы: 18

Бренд: RADVision Страницы: 3

Бренд: Intellitec Страницы: 16

magicbox aavelin

Бренд: ClearOne Страницы: 93

Бренд: FAAC Страницы: 63

Бренд: CAME Страницы: 28

Бренд: Jabbla Страницы: 54

Бренд: Discount Car Stereo Страницы: 6

Collaborate FHD

Бренд: ClearOne Страницы: 82

Бренд: Extron electronics Страницы: 18

Бренд: Cattron Страницы: 72

Бренд: New Rock Technologies Страницы: 71

Бренд: Aritech Страницы: 18

Бренд: Vicon Страницы: 44

Бренд: Sharp Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды