background image

EN

CHAIN SAW

USER'S MANUAL

7

Safety Instructions

3. SAFETY INSTRUCTIONS

 

ATTENTION!

 The safety instructions in this user’s manual are marked with the symbol containing critical 

points, which one needs to pay attention to when operating the power tool to prevent serious or fatal injuries. 
Please carefully study the instructions and adhere to them.

 

ATTENTION!

 This symbol indicates instructions that must be adhered to in order to prevent accidents that 

could result in serious or fatal injuries.

 

NOTE:

 This symbol indicates a tip or instructions useful when operating the power tool.

Before using the power tool

  Before using the power tool, carefully read the user’s manual.
  Do not use the power tool if your are under the infl uence of alcohol or narcotics, if you are tired or exhausted. 

Do not use the power tool if your are taking medication, which could affect or limit your decision-making 
abilities for safe operation of the power tool.

  Do not use the power tool indoors, the emitted gases contain damaging carbon monoxide.
  Never use the power tool under the conditions listed below:

–  If the work surface is slippery or if weather conditions do not permit you to maintain a stable stance while 

operating the power tool.

–  If it is dark, heavy fog or under poor weather conditions, which limit visibility of the work area.
–  During rain, during a storm or in strong winds or under conditions that could be dangerous when 

operating the power tool.

  If you are using the chain saw for the fi rst time, please consult with an experienced user before starting work.
  Tiredness or physical exhaustion may lead to inattentiveness, which may result in serious injury
  Limit the operating time of the power tool to approx. 10 minutes per single use and try to rest for 

approximately 10-20 minutes between work sessions. Limit the total amount of work per day to 
approximately 2 hours.

  Make sure that you have the user’s manual at hand in case you need to use it.
  If you sell, loan or handover the power tool, make sure that you include the user’s manual.
  Never allow children or other persons that are insuffi ciently acquainted with the user’s manual to use this 

power tool.

Safety of the operator, work equipment and clothing

  When operating a chain saw, you should wear the following work clothing and protective aids:

–  Helmet
–  Safety glasses or protective face shield
–  Work gloves
–  Anti-slip work boots
–  Earmuffs

Содержание FZP 4516 B


























Отзывы: