WARNING:
Never expose eyes or skin to UVC light from any source. Looking directly at the UVC light may cause permanent eye damage
or blindness.Never operate the UV-Aire
™
Air Purifying System out of the plenum. Avoid touching the glass portion of the lamp with your hands.
Page 3 of 12
INSTALLATION INSTRUCTIONS FOR PCUV-16UA PCO UPGRADE KIT
INSTALLATION INSTRUCTIONS FOR PCUV-16UA PCO UPGRADE KIT
NOTE: Please refer to the following Duo model installation instructions for specifi c instructions as directed
NOTE: Please refer to the following Duo model installation instructions for specifi c instructions as directed
below,
below, and the instructions included with the UV-Aire™ UV-16/24 or UV-16/120 models as directed below.
and the instructions included with the UV-Aire™ UV-16/24 or UV-16/120 models as directed below.
WARNING: Disconnect power to all equipment before beginning this installation! Refer to all warning
WARNING: Disconnect power to all equipment before beginning this installation! Refer to all warning
and
and cautionary statements as given in the included main installation instructions!
cautionary statements as given in the included main installation instructions!
1. If upgrading an existing installation of a UV-Aire™ UV-16 model with the PCO Carbon Upgrade Kit
1. If upgrading an existing installation of a UV-Aire™ UV-16 model with the PCO Carbon Upgrade Kit
(skip this
(skip this step for
step for new installations of a UV-16 model):
new installations of a UV-16 model):
a.
a.
CAREFULLY remove the ballast and lamp from the existing UV-16 model
CAREFULLY remove the ballast and lamp from the existing UV-16 model
, and remove its white
, and remove its white
plastic
plastic mounting base from the mounting surface.
mounting base from the mounting surface.
b.
b.
Determine whether the PCUV-16UA may be installed in the existing location
Determine whether the PCUV-16UA may be installed in the existing location
, using th
, using th included Duct
included Duct
Board Mounting Bracket as a template for the larger duct cutout required. Refer to the Installation
Board Mounting Bracket as a template for the larger duct cutout required. Refer to the Installation
Section in the following Duo installation instructions for guidance on installation location, required
Section in the following Duo installation instructions for guidance on installation location, required
clearances and safety precautions, etc.
clearances and safety precautions, etc.
c.
c.
If the PCUV-16UA may NOT be installed in the existing location
If the PCUV-16UA may NOT be installed in the existing location
, cover
, cover
and seal the existing
and seal the existingmounting
mounting location cutout with approprate materials,
location cutout with approprate materials,
and
and determine an alternate installation location as
determine an alternate installation location as directed.
directed.
2.
If attached, remove the UV-16 ballast from its white plastic mounting base by
twisting the ballast 1/4 turn to the left (counterclockwise), see labeling on the white
plastic mounting base and the Duo model installation instructions illustrations
.
3.
Peel paper backing from the included 1/2” x 1” rectangular foam gasket
and apply to the bottom of the new or existing UV-16 safety switch actuating
fi nger, on the underside of the white plastic mounting base as shown in Figure A.
NOTE: Do not remove the existing foam gasket from the base of the actuating
fi nger.
4. Using the four included #8-32 x 1/2” machine thread screws (fi ne threads),
attach the white plastic mounting base of the UV-16 to the PCUV-16UA mounting
fl ange as shown in Figure B. Note that the base may be attached in two different
orientations; refer to the Duo model instructions regarding the sight glass and
airfl ow direction.
5. Determine an appropriate mounting location as directed for the Duo model in
the Installation Section.
6. Using the included Duct Board Mounting Bracket as a template, mark and cut
the enlarged duct cutout required as directed for the Duo models.
FIG A
FIG B
P/N 46648100 09/18 Rev J
PRODUCT SIZING
The UV-Aire DUO products are designed to fi t into supply and return air ductwork as well as fi t into HVAC
systems. The UV-Aire DUO product insertion sizes and maximum HVAC system sizes are listed in Table 1
below. When selecting location for product installation, verify suffi cient room is available in system ductwork
to accommodate product insertion length to maintain proper HVAC airfl ow.
Model
HVAC System Sizing
(Tons)
Insertion Dimension
(Inches)
Hole Cut Out
Dimensions (Inches)
Static Pressure
Duo-11
1.0 to 3.0
11
5-3/8 x 5-3/8
0.015 “WC @ 1,200 CFM
Duo-14
1.0 to 5.0
13
5-3/8 x 5-3/8
0.017 “WC @ 2,000 CFM
Duo-16
1.0 to 5.0
15
5-3/8 x 5-3/8
0.02 “WC @ 2,000 CFM
PCUV-16A
1.0 to 5.0
15
5-3/8 x 5-3/8
0.02 “WC @ 2,000 CFM
TABLE 1: Sizing Table
