Fidelity Electronics DM-10K Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 52

background image

10. BATTERY POWER AND RECHARGING

Remaining battery power of the built-in rechargeable battery is displayed on
the

BATTERY POWER / LEVEL INDICATOR.

10.1 SYMBOLS AND REMAINING POWER: -

Full Battery:

≥ 6.3V

2 Blocks:

≥6.0V

1Block:

≥5.7V

Frame only:

＜

5.7V

10.2 BATTERY OPERATION TIME

Depends on the battery condition, a new and fully charged rechargeable
battery can provide: -



around 70 hours of continuous operation with backlight on, or



around 200 hours of continuous operation without backlight.

10.3 RECHARGE BATTERY

When                appears, (when  battery  is less than 5.7V),  it means  that the
built-in  rechargeable  battery  is  at low  voltage  status.  It  is  recommended  to
recharge as soon as possible.

To  protect  the  built-in  rechargeable  battery,  this  scale  will  be  powered  off
automatically  when  battery  is  at extremely  low  level.  If  this  is  the  case,  do
not attempt to power this scale on. Recharge this scale immediately. Fail to
do  so  may  cause  unrecoverable  damages  to  the  built-in  rechargeable
battery.

Battery  charging  status  is  shown  on  the  dual  color

CHARGE STATUS

INDICATOR

: -



Red: - Recharging in process,



Green: - Charging is completed.

Battery recharge is possible while operating. Overcharge protection circuit
is built inside to prevent battery damages caused by overcharge.

Heat will be generated during recharging and it is normal to feel minor heat
at front housing of this scale.

«
...
42
43
44
45
46
...
»

Содержание DM-10K





















































Отзывы:

Нет отзывов

Похожие инструкции для DM-10K

Бренд: Salter Brecknell Страницы: 4

Бренд: Optimum Страницы: 8

Бренд: Accuweight Страницы: 3

Бренд: Magnescale Страницы: 16

Бренд: TEC Страницы: 94

Бренд: EDLUND Страницы: 3

Бренд: INNOLIVING Страницы: 12

Бренд: Weighstation Страницы: 6

Бренд: OHAUS Страницы: 3

Бренд: Gravity Measurement Страницы: 11

Бренд: Gravity Measurement Страницы: 15

Бренд: Yamato Страницы: 4

Бренд: VOLTCRAFT Страницы: 4

Бренд: VOLTCRAFT Страницы: 4

Бренд: VOLTCRAFT Страницы: 8

Бренд: OBH Nordica Страницы: 24

Detecto ProDoc BFA PD150

Бренд: Cardinal Страницы: 50

Бренд: MyWeigh Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды