FIAM. x1R Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 25

FIAM. x1R Скачать руководство пользователя страница 6

6

ACTIVATING THE TAG “MASTER KEY”:

access the “programming” facility

A.

with the door open, press the spring latch

, with one finger and keep

it pressed, then bring any TAG (of those supplied) close to the receiver
located on the external plaque

(fig. 1).

B.

the acoustic alarm will emit a scale of rising sounds to tell you that the
lock is in the “programming” mode.

The lock will only remain in programming mode as long as you keep

the spring latch pressed. If you release the spring latch, you will auto-
matically leave the programming mode.

C.

so, while keeping the spring latch

, constantly pressed all the time, now

press the black and green buttons located on the internal plaque
(fig. 2) at the same time and keep them pressed for at least two sec-
onds. The acoustic alarm will emit one long tone to confirm.

D.

now chose any of the TAG x.Keys supplied and bring it close to the receiver
located on the external plaque

. The acoustic alarm will emit two short

tones to confirm programming of the TAG as the “master key”.

release the pressure on the spring latch

to exit the programming mode.

ACTIVATING THE “SERVICE” TAGS:

access the “programming” facility

A.

With the door open, hold spring latch

down with one finger and

bring the TAG programmed before at a “master” level near the receiv-
er on the external plaque

(fig. 1).

B.

the acoustic alarm will emit a scale of rising sounds to tell you that the
lock is in the “programming” mode.

The lock will only remain in programming mode as long as you keep

the spring latch pressed. If you release the spring latch, you will auto-
matically leave the programming mode.

C.

so, while keeping the spring latch

constantly pressed all the time,

now press the black button located on the internal plaque

(fig. 3).

and keep it pressed for at least one second: the buzzer emits just one short
tone (1 beep). Every TAG that you bring close to the receiver (fig. 1) will
be registered at the “service” level. The buzzer confirms programming
of each TAG by means of a short sound (1 beep). Once the program-
ming phase has been completed, proceed to enabling all the TAGs pro-
grammed at a “service” level, by holding down for at least one second
the black button on internal plaque

(fig. 3). The buzzer emits two

brief sounds (2 beeps).

NOTE:
If at the start of phase C the buzzer emits TWO short sounds (2 beeps) press
the black key again so that the buzzer only emits ONE short sound (1
beep), confirming that the lock is now set up for programming new “ser-
vice” TAGS

release the pressure on the spring latch

to exit the programming mode.

P

5

p

2

2

5

1

5

P

5

1

2

5

1

5

p

BASIC PROGRAMMING

FIG.1

FIG.2

FIG.3

«
...
4
5
6
7
8
...
»

Содержание x1R


























Отзывы:

Нет отзывов