Festo IFB05-03 Скачать руководство пользователя страница 99

Страница: 99 / 154

5. Diagnosis and error treatment

5−5

Festo P.BE−VIFB5−03−EN en 0503e

LEDs
green

red

Operating status

Error treatment

Operating  status  normal  or:
operating  status  normal  but  valves  do
not  switch.
Possible  causes
Operating  voltage  of  the  outputs

not in tolerance range or not ap
plied.

Compressed air supply not correct.
Pilot exhaust blocked.

None

Check the ...

operating  voltage  connection  of  the
outputs  (pin  2),  tolerance  range
21.6V  DC  ...  26.4  V)

the compressed air supply

pilot exhaust channels

Operating voltage not applied

Check the operating voltage connec
tion for the electronics (pin 1)

(very fast)

Baud  rate  setting  and/or  address  se
lector  switch  setting  are  not  permitted
with  the  field  bus  protocol  set

Check the address/baud rate settings

(1 second i

Field  bus  connection  not  correct.
Possible  causes
Address  setting  is  not  correct

(e.g. address assigned twice)

The baud rates set on the valve ter

minal and on the field bus module
are not the same.

Field bus protocol setting is not cor

rect

Switched−off or defective field bus

module

Interrupted, short−circuited or

faulty field bus connection

Check the ...

setting of the address selector
switch

baud rate setting on the valve ter
minal and on the field bus module

field bus protocol setting

field bus module

field bus connection

out

flashes red

flashes green

lights up green

lights up red

Fig.5/3: LED display of operating status (part 1)

Содержание IFB05-03



























































































































































Результаты поиска

Содержание IFB05-03

Отзывы:

Бренды по названию

Популярные бренды

Festo IFB05-03, Руководство пользователя

Результаты поиска

Содержание IFB05-03

Отзывы:

Бренды по названию

Популярные бренды