Festo IFB05-03 Скачать руководство пользователя страница 129

Страница: 129 / 154

A. Technical appendix

A−3

Festo P.BE−VIFB5−03−EN en 0503e

A.1

Technical specifications

General

Protection class

(as per

EN60529)

Temperature

during

operation
storage/transport

IP 65

− 5°C ... +50°C
−20°C +60°C

Vibration

(as  per  DIN/IEC68/EN60068
part  2−6  and  as  per
IEC721/EN60068  part  2−3)
Transport

Operation/use

Shock

(as per DIN/IEC 68/EN60068
part 2−27 and IEC 721)

3,5mm  path  at  2−8Hz
1g  acceleration  at  8−25Hz
0,35mm  path  at  25−57Hz
5g  acceleration  at  57−150  Hz
1g  acceleration  at  150−200Hz

30g at 11ms duration

Protection against electric
shock

(protection  against  direct  and
indirect  contact  as  per  IEC/DIN
EN  60204−1)

by means of PELV circuits
(ProtectiveExtra−Low Voltage)

Elektromagnetic compatibility

Interference emitted

Immunity against interfe

rence

Tested as per DIN EN 61000−6−4
(industry)

Tested as per DIN EN 61000−6−2
(industry)

The component is intended for industrial use.

Содержание IFB05-03



























































































































































Результаты поиска

Содержание IFB05-03

Отзывы:

Бренды по названию

Популярные бренды

Festo IFB05-03, Руководство пользователя

Результаты поиска

Содержание IFB05-03

Отзывы:

Бренды по названию

Популярные бренды