manualshive.com logo in svg

Festo CRDNG Series, Инструкции по ремонту, Страница: 7 / 26

Поделиться
Скачать
Festo CRDNG Series Скачать руководство пользователя страница 7

7 / 26

Festo 7CRDNGb_en

2.2 

Type codes (ascertaining the features of a cylinder)

The precise features of the current cylinder with piston rod can be ascertained with the help of the rating plate on 
the cylinder. The type designation is located directly beneath the Festo logo and describes the cylinder's features 
separated by a hyphen (-).

Example:

CRDNG-80-100-PPV-A-S6

185297     AN08

max. 10 bar / 145 psi

1

4

2
3

1

  Type designation

2

  Serial number

3

  Technical information

4

  Part number

The type designation on this rating plate provides the following information:

CRDNG

 

Cylinder of the type CRDNG

80

 

Piston diameter 80 mm

100

 

Stroke 100 mm

PPV

 

Adjustable end-position cushioning

A

 

Sensing option (magnetic piston)

S6

 

Heat-resistant seals (repair-relevant feature (see chapter 

2.3 "Repair-relevant features"

))

Note

A list and description of all possible equipment features of the cylinder with piston rod can be found in the data sheet. 
It is available on the Festo website (

www.Festo.com

).

2.3 

Repair-relevant features

Some of the features that the cylinder with piston rod can be equipped with require a different repair approach. These are 
referred to as "repair-relevant" features and are listed in the left-hand column in the table below.
If the cylinder to be repaired has one of these repair-relevant features, the appropriate repair description (see right-hand 
column in the table below) must be used.

Note

A cylinder can only have one repair-relevant feature. It can additionally be equipped with one or more other features 
(see middle column).

Cylinder and repair-relevant feature

Other features

Described from page

CRDNG-… without repair-relevant feature

PPV, A, S2

11

CRDNG-…-

S6

 (heat-resistant seals up to max. 120°C)

PPV, A

17

CRDNGS-… without repair-relevant feature

PPV, A

11

CRDNGS-…-

S6

 (heat-resistant seals up to max. 120°C)

PPV, A

17

Example for the cylinder in chapter 

2.2 "Type codes (ascertaining the features of a cylinder)"

Of the features in the sample cylinder, the feature "S6" is relevant to the repair. The description in chapter 

4.4 "Repairing 

the cylinder CRDNG(S)-…-S6"

 on page 

17

 must therefore be used to repair this cylinder with piston rod.

Содержание CRDNG Series



























Отзывы:

Нет отзывов