manualshive.com logo in svg

Festo CRDNG Series, Инструкции по ремонту, Страница: 12 / 26

Поделиться
Скачать
Festo CRDNG Series Скачать руководство пользователя страница 12

12 / 26

Festo 7CRDNGb_en

4.3.1 

Structure of the bearing cap

Note

In some series and variants the bearing and end caps may differ from the versions shown here. The precise design 
of the bearing and end caps must be determined before each repair using the parts lists in the online spare parts 
catalogue on the Festo website (

spareparts.festo.com

) and taken into consideration during the repair. 

Bearing cap CRDNG(S)-…

1

2

4

5

3

1

  Bearing cap

2

 O-ring

3

  Cushioning seal

4

  Piston rod seal

5

 Bearing

Bearing cap CRDNG-125-…-PPV-A-S2

1

2

6

7

8

4

5

3

1

  Bearing cap

2

 O-ring

3

  Cushioning seal

4

 Sleeve

5

 O-ring

6

  Piston rod seal

7

 Bearing

8

 Adapter

4.3.2 

Removing the bearing and end caps

• 

Loosen the screws in the bearing cap from the tie rods (hold the screws in 
the second bearing cap in place on cylinders with through piston rod (S2 )) 
and remove them.

• 

Remove the bearing and end caps (both bearing caps on cylinders with 
through piston rod (S2)) from the cylinder barrel and piston rod.

• 

Loosen the tie rods in the end cap and remove them (on cylinders with 
through piston rod (S2), pull the tie rod with the screws out of the second 
bearing cap and unscrew the screws from the tie rod).

• 

Remove any residue of the screw locking agent from the threads of 
the screws and tie rods.

Содержание CRDNG Series



























Отзывы:

Нет отзывов