Bus module
CPX-E-PB
Festo AG & Co. KG
Ruiter Straße 82
73734 Esslingen
Germany
+49 711 347-0
www.festo.com
Instructions for use
Original instructions
8071115
2017-07
[8071117]
Bus module CPX-E-PB (PROFIBUS DP)
English
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
About this document
This document describes the use of the above-mentioned product. Certain aspects
of use are described in other documents and must be observed
è
1.1 Further applicable documents.
PI PROFIBUS PROFINET
®
is a registered trademark of its respective trademark
holder in certain countries.
1.1 Further applicable documents
Document
Content
Description of system CPX-E (CPX-E-SYS)
Detailed description of the system CPX-E
Instructions for use of system CPX-E
(CPX-E-SYS)
Instructions and important notes on mounting,
electrical installation and maintenance tasks
for a system CPX-E
Description of bus module CPX-E-PB (CPX-E-PB)
Detailed description of product function and
parameterisation options
Device description file (GSD)
Definition of the modules of a system CPX-E for
integration into the higher-order controller
Documentation for the components in a system
CPX-E and the connected peripherals
Information on use of the components
Documentation for the higher-order controller
and the additional participants in the network
Information on commissioning and
parameterisation of the components
Fig. 1
All available documents for the product
è
www.festo.com/pk.
1.2 Product version
This document refers to the following product versions:
Product
Version number
CPX-E-PB
Bus module CPX-E-PB, revision 3 onward
Fig. 2
The product version can be identified from the product label or with the help of
appropriate software from Festo.
Appropriate software for identifying the product version can be found in
the Festo Support Portal
è
www.festo.com/sp. Information on using the
software can be found in the integrated Help function.
There may be an updated version of this document for these or later
product versions.
Check whether a corresponding version of this document is available
inthe Festo Support Portal
è
www.festo.com/sp.
1.3 Product labelling
The product label is located on the left-hand side of the module. Scanning the
printed Data Matrix Code with an appropriate device opens the Festo Support
Portal with the relevant documents for the product. Alternatively, the Product Key
(11-character alphanumeric code on the product label) can be entered in the
Support Portal search box.
Detailed information about product labelling can be found in the module
description
è
1.1 Further applicable documents.
1.4 Specified standards
Version status
EN 60529:2013-10
IEC 60204-1:2014-10
EN 61000-6-2:2009-04
IEC 61158:2014-07
EN 61000-6-4:2011-09
NE 21:2012-05
Fig. 3
2
Safety
2.1 General safety information
Take into consideration the legal regulations for the respective location.
Use the product only within the defined values
è
13 Technical data.
Observe product labelling.
Observe further applicable documents
è
1.1 Further applicable documents.
Store the product in a cool, dry, UV-protected and corrosion-protected
environment. Ensure storage times are short.
Before working on the product: Switch off the power supply and secure it
against being switched on again.
Observe the handling specifications for electrostatically sensitive devices.
2.2 Use for intended purpose
The product described in this document is intended solely for use as an interface
between a system CPX-E and a higher-order controller through participation in
aPROFIBUS DP network.
The products must be used only as follows:
– Use only in an industrial environment: Outside of industrial environments, e.g. in
commercial and mixed-residential areas, actions to suppress interference may
have to be taken.
– Use only in combination with modules and components that are permissible for
the respective product variant
è
www.festo.com/catalogue.
– Only use the product if it is in perfect technical condition.
– Only use the product in its original condition without unauthorised
modifications. Only the conversions or modifications described in this and the
further applicable documents are permitted.
2.3 Training of specialised personnel
Installation, commissioning, maintenance and disassembly should only be
conducted by qualified personnel.
The qualified personnel must be familiar with installation of electrical control
systems.
3
Further information
– Accessories
è
www.festo.com/catalogue
– Spare parts
è
www.festo.com/spareparts
4
Service
Contact your regional Festo contact if you have technical questions
è
www.festo.com.
5
Product overview
5.1 Function
The product establishes, as a participant in a PROFIBUS DP network, the
connection between a higher-order controller and the modules of a system CPX-E.
5.2 Product design
1
LED indicators
2
DIL switch
3
Diagnostic interface [DIAG]
(mini-USB)
4
Operating voltage supply terminal
block U
EL/SEN
[XD]
5
Terminal block lock
6
Linking
7
Network connection [XF1]
2
3
4
5
1
6
7
Fig. 4
5.3 Display components
1
Network-specific LED indicator:
– Bus error [BF] (red)
2
System-specific LED indicators:
– Operating voltage supply
U
EL/SEN
[PS] (green)
– Load voltage supply U
OUT
[PL]
(green)
– System fault [SF] (red)
– Force mode [M] (yellow)
2
1
Fig. 5
